Cardinal 2XX-IP Скачать руководство пользователя страница 11

8200-M503-01 Rev-B 

 2XX-IP 

9

TROUBLESHOOTING 

Status LED’s 

The 2XX-IP contains two LED’s to indicate the communication status of the 10/100BaseT 
Ethernet TCP/IP connection. 
 

ETHERNET LINK (D3)

 - This LED will illuminate 

when the 2XX-IP has been successfully 
connected to a network and flicker when data is 
being transmitted or received over the network. 

 

MASTER (D4)

 - This LED will flash with every 

communication between the 2XX-IP and the 
indicator.  If the MASTER LED is not flashing, 
then communications between the 2XX-IP and 
the indicator has failed. 

 
 

XPORT Status LED’s 

LED’s are provided on the edge of the XPORT connector for diagnostics.  Their status and 
meaning are listed below. 
 
 

LEFT LED 

RIGHT LED   

MEANING 

Off 

 

  Off 

 

 No 

Link 

Off  

 

Solid Amber   

100BASE-T Half Duplex Link 

Off  

 

Blinking Amber  

100BASE-T Half Duplex; Activity 

Off  

 

Solid Green    

100BASE-T Full Duplex Link 

Off  

 

Blinking Green  

100BASE-T Full Duplex; Activity 

 

Solid Amber   

Off  

 

10BASE-T Half Duplex Link 

Blinking Amber 

Off  

 

10BASE-T Half Duplex; Activity 

Solid Green    

Off  

 

10BASE-T Full Duplex Link 

Blinking Green  

Off  

 

10BASE-T Full Duplex; Activity 

 
 

RIGHT
LED

LEFT 
LED 

Содержание 2XX-IP













Отзывы: