background image

17

LED Status Indicator Operation:

LED is off = Alarm is disarmed.
LED is flashing = Alarm is armed.
LED is flashing in a 2 flash hold sequence = Tamper warning, alarm was triggered by the hood/  

trunk or electronic sensor.

LED flashing in a 3 flash hold sequence = Tamper warning, alarm was triggered by an open door.
LED is on steady = Alarm is in the valet mode. (Ignition key is “on”)
LED flashes once every 5 seconds = Alarm is in the valet mode. (Ignition key is “off”)
LED is flashing fast = Automatic arming timer is counting down or RF tamper rearming timer is counting

down.

Parking Light Flash Alarm Status Indication:

One light flash = Alarm is armed.
Two light flash = Alarm is disarmed.
Three light flash = Tamper w alarm is disarmed.

Siren Chirp Alarm Status Indication:

Note: This feature can be programmed off, see “Remote Feature Programming” for details.
One chirp = Alarm is armed and all input trigger wires are clear.
Two chirps = Alarm is disarmed and has not been tampered with.
Chirps once, pauses then chirps again = Alarm is armed but sensor is by-passed.
Four chirps = Tamper indicator, alarm is disarmed.

Power Door Lock/Unlock:

(If Installed)

1. Press the lock button on the transmitter, the locks will become locked.

2. Press the unlock button on the transmitter, the locks will become unlocked.

RF Tamper Re-Arm:

Note: This feature is activated automatically when the alarm is programmed for automatic arming. See

“Remote Feature Programming” for details.

1. Alarm must be programmed for automatic arming. 

2. Close all protected entrances and press the lock button on the remote transmitter. The LED will be

flashing at a normal rate.

3. Wait 5 seconds and press the unlock button on the remote transmitter. The LED will begin to flash fast.

(Automatic arming indicator)

4. Wait 60 seconds and the alarm will become rearmed.

5. Repeat steps 1 through 4. When the LED starts flashing fast, open one of the protected entrances

(door) the LED will be off and remain off.

60 Second Re-Arm Timer and Re-Lock Function:

Once the alarm is triggered, the siren will sound for 60 seconds and then stop. The alarm will remain in

an armed condition. If the door locks have been installed into the system, they will re-lock when the

alarm resets after 60 seconds.

Step 9: Speciality Feature and Optional Equipment Testing

Содержание PLUS-4500





















Отзывы: