background image

15

Each specialty feature listed operates in the same manner regardless of the alarm model. Test each feature

by following the procedures enclosed to insure proper operation.

Remote Panic:

1. Press and hold the lock or panic button down for approximately 3 seconds.

2. The alarm will begin to sound and the parking lights will begin to flash.

3. Press the unlock or panic button once again and the siren will stop sounding and the lights will stop

flashing.

Note: The remote panic feature has an automatic shut off circuit. When the siren has sounded for 60

seconds, the panic circuit will turn itself off automatically.

Last Door Automatic Arming: 

(If Programmed On) 

Note: The automatic arming feature will not operate unless the alarm input triggers have been connected

directly to the existing or newly installed door jamb pins. Current sensing alone will not activate the

automatic arming circuit.

1. Press the unlock button to disarm the alarm.

2. Set the ignition key to the on position, then turn it off.

3. Exit the vehicle. The siren will chirp 1 time when the door is closed.

4. The LED will begin to flash fast.

5. After 10, 20 or 30 seconds have passed (depending on remote feature programming), you will hear a

single chirp. The alarm is now armed.

6. The LED will flash at a regular rate indicating an armed condition.

Note: When the automatic arming feature is activated, so is the RF tamper re-arm circuit. Every time the

alarm is disarmed by remote, the RF tamper re-arm circuit will count for sixty seconds (LED will be

flashing fast) and the alarm will re-arm itself if no one has entered the vehicle. 

To test the basic functions of the alarm system (all models) repeat the following procedures:

1. Turn off the ignition key and exit the vehicle closing all protected entrances.

2. Press the lock button on the transmitter. You will hear a siren chirp, the parking lights will flash one

time and the LED status indicator will flash at normal speed.

3. Wait 5 seconds, then open a protected entrance. The siren will begin to sound. Press the unlock button

once again and the siren will stop sounding. (No Disarm Chirp Indicator)

Note: If you press the unlock button when the siren is sounding, there are no disarming chirps. When

you press the unlock button when the siren is off, there will be disarming chirps.

4. Follow procedures 2 and 3 for all other protected entrances.

Step 8: General Testing

Step 9: Speciality Feature and Optional Equipment Testing

Содержание PLUS-4500





















Отзывы: