CanyCom S160 Скачать руководство пользователя

Страница: 68 / 75

-59-

Troubleshooting

• If any malfunction or abnormal condition is found, immediately stop using the

machine and take an appropriate measure according to the Troubleshooting chart
below. If the malfunction or abnormal condition is not listed in the chart, or the
suggested measure does not solve the problem, consult with your CANYCOM
representative.

• Some corrective measures listed below require special knowledge and/or

equipment. Please contact your CANYCOM representative in such a case.

Area

Malfunction

Possible Cause

Corrective Measure

Ref.

Engine

Engine does not start, or
is difficult to start.

Parking brake lever
is angaged (safety
mechanism is on).

→Disengage parking

brake.

Page 20

Battery is discharged.

→Add battery fluid.
→Charge Battery.
→Replace battery.

Page 54

Battery cable is
disconnected.

→Connect battery cable.

Blown fuse.

→Replace fuse.

Page 56

Bad connection
orbreakage in the wiring.

→Please contact

your CANYCOM
representative.

Out of fuel.

→Fill fuel.

Page 15

Air is in fuel.

→Please contact

your CANYCOM
representative.

Insufficient or wrong oil.

→Fill or change oil

Page 41

Contamination in fuel
system.

→Please contact

your CANYCOM
representative.

Other (other than the
above).

→Please contact

your CANYCOM
representative.

Engine stalls.

Out of fuel.

→Fill fuel

Page 15

Engine is cold.

→Warm up engine.

Choke lever is in [Close]
position.

→Please contact

your CANYCOM
representative.

Содержание S160












































































Результаты поиска

Содержание S160

Отзывы:

Похожие инструкции для S160

Бренды по названию

Популярные бренды

CanyCom S160, Руководство оператора

Результаты поиска

Содержание S160

Отзывы:

Похожие инструкции для S160

Бренды по названию

Популярные бренды