CanyCom S160 Скачать руководство пользователя страница 65

Страница: 65 / 75

Maintenance

-56-

Fuses

1. Open engine cover.
2. Open the lid of fuse housing.

• If a fuse blows, investigate the cause before replacing. Always replace a fuse

with the one of the correct rating.

• Rapid charging is only an emergency measure. This method uses a large amount of

current to compensate the lost charge in a short time. However, the battery needs
to be fully charged in the ordinary method for a longer service life.

NOTE

3683M-0508-030E

Fuse Housing

1.  Remove battery from the machine.
2.  Remove all filler plugs.
3.  Follow  the  instructions  in

the battery

charger user's manual

to charge the

battery.

4. When battery is fully charged, put filler plugs

back in place and install battery.

Charging

UPPER LEVEL

LOWER LE

VEL

‑

3570M-0509-030E

3683M-0508-040E

Fuses

3. Locate the blown fuse and replace it with a

new one of the correct rating.

4. Put the lid back in place.
5. Close engine cover.

• Replacement Fuse: 40A (2pcs.)

NOTE

Содержание S160












































































Результаты поиска

Содержание S160

Отзывы:

Похожие инструкции для S160

Бренды по названию

Популярные бренды

CanyCom S160, Руководство оператора

Результаты поиска

Содержание S160

Отзывы:

Похожие инструкции для S160

Бренды по названию

Популярные бренды