CanyCom S160 Скачать руководство пользователя страница 59

Страница: 59 / 75

Maintenance

-50-

5. Wipe excess oil around inspection hole.

Clean inspection plug and filler cap. Put
inspection plug and filler cap back in place
and tighten them securely.

• Oil Capacity: 3.3L
• Oil to Use: Gear Oil, API rating GL-4 or 5,

SAE index #80.

1.  Have an appropriate oil drain pan ready.
2.  Remove drain plug to drain oil.
3.  Clean drain plug and seal washer. Put drain

plug back in place and tighten it securely.
Watch for leaks.

3683M-0507-070E

Drain Plug

Draining

NOTE

Filling

1. Remove filler cap and inspection plug.
2. Fill oil slowly until oil flow out of inspection

hole.

3. Wipe around inspection hole.
4. Clean inspection plug and seal washer. Put

inspection plug back in place and tighten it
securely. Watch for leaks.

5. Put filler cap back in place.
6. Install floor panel.

• Removing filler cap helps drain oil.

NOTE

Содержание S160












































































Результаты поиска

Содержание S160

Отзывы:

Похожие инструкции для S160

Бренды по названию

Популярные бренды

CanyCom S160, Руководство оператора

Результаты поиска

Содержание S160

Отзывы:

Похожие инструкции для S160

Бренды по названию

Популярные бренды