manualshive.com logo in svg

CanyCom S160, Руководство оператора, Страница: 67 / 75

Поделиться
Скачать
CanyCom S160 Скачать руководство пользователя страница 67

Maintenance

-58-

5

Storage

1.  Follow the instructions in 

Parking

 (page 28) to park the machine.

2.  Clean dirt off of the machine. 
3.  Change engine oil (page 41).

 • Do not wash the engine or control panel with running water; water may enter 

inside and cause rust or damage.

 • Clean the machine before storage; leaving dirt or foreign objects may cause 

rust or damage.

 • Do not store the machine in a humid, dusty, or hot place.

 

• Fire hazard; do not store the machine where there is a possiblity of ignition.

 • Battery dischages even when it is not in use. A battery may hold charge for a few 

months, but it is a good practice to charge battery before it goes flat; it will extend 
the battery life.

 • Refer to the Operation Manual for the engine, for detailed instructions on preparing 

the engine for storage. 

 • Do not forget to turn the fuel cock to "ON" position when starting the machine. 

NOTE

3683M-0509-010E

Off

On

Fuel Cock

4.  Clean the air cleaner (page 43).
5.  Open  engine  cover  and  turn  fuel  cock  to 

"OFF" position. Close engine cover.

6.  Remove battery from the machine. Service 

battery (page 54).

7.  Cover the machine with protective, water-

proof covering after the machine is cooled 
off.

Содержание S160












































































Отзывы:

Нет отзывов