CanyCom CMX 224 Скачать руководство пользователя страница 75

Страница: 75 / 93

Maintenance

-66-

Cutting Rotary Drive Belt

• Adjust belt tension properly. Inproperly tensioned belt may reduce performance

and its service life.

1.  Open engine hood.
2.  Move cutting rotor clutch lever to [ON].
3.  Check V-belt tension. Push V- belt  by finger

and check that deflection at center point A is
in the range of 10 to 15 mm. If it is out of this
range, adjust with adjust nut.

4. Visually inspect belt. Replace belt if it is

damaged. For replacement, contact your
CANYCOM representative.

5. Move cutting rotor clutch lever to [OFF].
6. Close engine hood.

Inspecting

5332M-0508-110E

Ａ

Lock Nut

Adjust Nut

Adjusting

1.  Open engine hood.
2.  Move cutting rotor clutch lever to [ON].
3.  Loosen lock nut.
4.  Adjust V-belt with adjust nut so that the

deflection at center point A is in the range
of 10 to 15 mm when the belt is pressed by
finger.

5.   Tighten lock nut.
6.  Move cutting rotor clutch lever to [OFF].
7.  Close engine hood.

Содержание CMX 224






























































































Результаты поиска

Содержание CMX 224

Отзывы:

Похожие инструкции для CMX 224

Бренды по названию

Популярные бренды

CanyCom CMX 224, Руководство оператора

Результаты поиска

Содержание CMX 224

Отзывы:

Похожие инструкции для CMX 224

Бренды по названию

Популярные бренды