CanyCom CMX 224 Скачать руководство пользователя страница 71

Страница: 71 / 93

Maintenance

-62-

1. Park machine on level ground.
2. Remove left step.

5332M-0507-070E

Adjust Nut

Lock Nut

3. Loosen lock nut
4. Adjust with adjust nut when brak peddal is

free so that the brake does not drag.

5. Adjust brake so that the brake works and the

brake pedal locks securely when brake pedal
is locked

6. Tighten lock nut.

Rear Brake

• If brake does not work even the brake

pedal is locked, the brake shoe is worn
out. Please contact your CANYCOM
representative for replacement.

• Always keep brake adjusted for maximum performance. Improperly adjusted

brakes may result in property damage, serious injury, or death.

Parking Brake

Front Brake (CMX 224)

7. Lock brake pedal and Inspect that the strech

of spring is between 5mm and 8mm. If it is
not within this range, adjust it with adjust nut.

8. Tighten lock nut after adjustment
9. Install left step back in place.

Spring

5332M-0507-060E

Adjust Nut

Lock Nut

NOTE

Содержание CMX 224






























































































Результаты поиска

Содержание CMX 224

Отзывы:

Похожие инструкции для CMX 224

Бренды по названию

Популярные бренды

CanyCom CMX 224, Руководство оператора

Результаты поиска

Содержание CMX 224

Отзывы:

Похожие инструкции для CMX 224

Бренды по названию

Популярные бренды