CanyCom CMX 224 Скачать руководство пользователя страница 43

Страница: 43 / 93

Operation

-34-

Working

Inspecting Cutting Blade

Inspect cutting blade before work. Refer to

Cutting Blades

(page 63) for inspection

procedure.

Adjusting Cutting Height

5332M-0403-010E

Cutting Height Lock

Cutting Height Adjust Lever

1. Grab cutting height lock to unlock cutting

height adjust lever.

5332M-0403-020E

Cutting Height Adjust Lever

2. With lock button pulled up, move cutting

height adjust lever to a desired position.

3. Release lock to lock cutting height adjust

lever.

•  Cutting Height Range: 0mm - 150mm (CMX224, CM225)
    0mm - 130mm (CM184)
•  Cutting Height indicated on the side of the adjust lever is for reference purpose

only; actual cutting height may vary due to the condition of ground or brush, and
other factors.

NOTE

Содержание CMX 224






























































































Результаты поиска

Содержание CMX 224

Отзывы:

Похожие инструкции для CMX 224

Бренды по названию

Популярные бренды

CanyCom CMX 224, Руководство оператора

Результаты поиска

Содержание CMX 224

Отзывы:

Похожие инструкции для CMX 224

Бренды по названию

Популярные бренды