CanyCom CMX 224 Скачать руководство пользователя страница 39

Страница: 39 / 93

Operation

-30-

1. Stop machine.
2. Move auxiliary transmission shift lever to [H

(high speed)] or [L (low speed)] position firmly.

5332M-0402-100E

Auxiliary
Transmission
Shift Lever

• See Specifications (page 15) for the speed

range in either gear position.

• Always stop machine to shift between 2WD or AWD (all-wheel-drive) modes.

Shifting gears while machine is in motion can damage transmission.

• Use 2WD mode under normal condition.

• Pay attention to the minimum turning radius in AWD mode. In AWD mode,

minimum turning radius is greater than that in 2WD mode.

Shifting Between 2WD and AWD (CMX224)

• Always stop machine to shift gears. Shifting gears while machine is in motion

can damage transmission.

NOTE

• Always shift gears firmly. When transmission is not firmly shifted, it may jump

out of gear, resulting in loss of control of machine.

Shifting

Содержание CMX 224






























































































Результаты поиска

Содержание CMX 224

Отзывы:

Похожие инструкции для CMX 224

Бренды по названию

Популярные бренды

CanyCom CMX 224, Руководство оператора

Результаты поиска

Содержание CMX 224

Отзывы:

Похожие инструкции для CMX 224

Бренды по названию

Популярные бренды