Chapter 4
4-9
SW504 on the saddle stitcher con-troller PCB as
follows:
F-4-15
3) Remove the rear cover, open the inlet cover of the
saddle stitcher unit and tape the actuator of inlet cover
sensor (PI9) and inlet door switch (MSW1).
4) Before inserting the paper, mark the top of the
paper. You will be using two sheets of A3 or LDR
paper.
F-4-16
5) Turn on the power of the host machine.
6) Press SW1 on the saddle stitcher controller PCB so
that the feed motor (M1) starts to rotate. (Press SW1
three seconds or more if LDR paper is used.)
7) Open the inlet cover and insert two sheets of paper.
Push them in by hand until the front edge of the sheets
push against the paper positioning plate.
8) Close the inlet cover.
9) Press SW1 on the saddle stitcher controller PCB.
The saddle stitcher unit will "stitch" the sheets, and
fold and deliver the stack automatically.
10) Measure the distance (L) between the stitching
position and the folding position. Then perform
"positive width adjustment" or "negative width
adjustment" to suit the relationship between the
stitching position and the folding position.
If the stitching position is below the folding position,
perform "positive width adjustment."
If the stitching position is above the folding position,
perform "negative width adjustment."
F-4-17
11) Change the settings of bits 6 through 8 on SW504
referring to the following table.
If the width adjustment is 0
The stitching position and the folding position match,
requiring no change.
If for "positive width adjustment"
Set SW504 so that the difference resulting from
subtraction of the interval from the appropriate setting
in the above figure is provided.
Example: If SW504 is currently set to +2 and the
interval is +1 mm, set SW504 to reflect -2.
If for "negative width adjustment"
Set SW504 so that the sum resulting from addition of
the interval from the appropriate setting in the above
fingure is provided.
Example: If SW504 is currently set to -1 and the
interval is -0.5mm, set SW504 to r1.
ON
1 2 3 4 5 6 7 8
Do not change bits 5 through 8.
Mark
A3/LDR paper
Insert direction
Mark
Folding position
Stitching position
Positive Width Adjustment
Unit: mm
Example: If L is 1 mm, provide “+1 mm”.
Mark
Stitching position
Folding position
Negative Width Adjustment
Unit: mm
Example: If L is 0.5 mm, provide “-0.5 mm”.
Содержание Saddle Finisher-T2
