Canon Paper Deck Unit-F1 Скачать руководство пользователя страница 54

Страница: 54 / 112

Motors

Removing the Deck Lifter

Motor

■ Preparation

CAUTION:

The Lifter Plate must be moved to the bottom before
removing the Lifter Wire.

1. Open the Compartment with the open button and

then remove all sheets of paper from it.

2. Press the relay paper sensor until the lifter reaches

to the bottom position.

3. Turn OFF the host machine and remove the lattice

connector.

4. Remove the Compartment.

“Removing the

Compartment ” on page 43

■ Procedure

1. Remove the Deck Lifter Motor Assembly[1].

• 4 Wire saddles[2]
• 1 Reuse band[3]
• 3 Connectors[4]
• 5 Screws[5]

[1]

[4]

[5]

[4]

[2]

[3]

[5]

4. Disassembly/Assembly

Содержание Paper Deck Unit-F1
















































































































Результаты поиска

Содержание Paper Deck Unit-F1

Отзывы:

Похожие инструкции для Paper Deck Unit-F1

Бренды по названию

Популярные бренды

Canon Paper Deck Unit-F1, Руководство по обслуживанию

Результаты поиска

Содержание Paper Deck Unit-F1

Отзывы:

Похожие инструкции для Paper Deck Unit-F1

Бренды по названию

Популярные бренды