Canon Paper Deck Unit-F1 Скачать руководство пользователя страница 46

Страница: 46 / 112

2. Remove the Deck Pickup Roller[1].

• 1 Claw[2]

[1]

[2]

NOTE:

How to install the Deck Pickup Roller
Be sure to align the protrusion [2] of the Deck Pickup Roller
[1] with the groove [3] of the gear to install the roller.

[1]

[2]

[3]

Be sure to insert the Deck Pickup Roller [1] until the claw
[2] is hooked.

[1]

[2]

■ Actions when Replacing the Parts

1. Clear the parts counter.

(LV1) COPIER > COUTER > DRBL-2 > PD-PU-RL

Removing the Deck

Separation Roller

■ Preparation

1. Remove the Left Upper Cover.

“Removing the Left

Upper Cover” on page 36

2. Remove the Deck Feed Roller.

“Removing the Deck

Feed Roller ” on page 38

■ Procedure

CAUTION:
Be sure not to touch the surface of the roller at
disassembling/assembling.

1. Slide the Slide Guide (Lower)[1] in the direction of

the arrow and keep it.

4. Disassembly/Assembly

Содержание Paper Deck Unit-F1
















































































































Результаты поиска

Содержание Paper Deck Unit-F1

Отзывы:

Похожие инструкции для Paper Deck Unit-F1

Бренды по названию

Популярные бренды

Canon Paper Deck Unit-F1, Руководство по обслуживанию

Результаты поиска

Содержание Paper Deck Unit-F1

Отзывы:

Похожие инструкции для Paper Deck Unit-F1

Бренды по названию

Популярные бренды