Canon Paper Deck Unit-F1 Скачать руководство пользователя страница 49

Страница: 49 / 112

Opening the Compartment

■ Procedure

1. Insert screwdrivers into the hole at rear left side of

the compartment[2] and then release the lever[1] to
open it.

NOTE:

• Insert screwdrivers into the hole at arrowhead

marking.

• The lever locates above the hole, so insert

screwdriver upward through the hole.

[2]

[1]

Removing the Compartment

■ Preparation

1. Open the Compartment.

“Opening the

Compartment ” on page 43

2. Removing the Right Cover.

“Removing the Right

Cover ” on page 36

■ Procedure

1. Open the Compartment[1] until it stops while

releasing stoppers[2] with pressing left and right
Latches.

4 Screws[3]

[1]

[2]

[3]

2. Set sheets of paper (approx.6cm) under both side of

the Compartment to prevent deformation of the
wheel plate.

4. Disassembly/Assembly

Содержание Paper Deck Unit-F1
















































































































Результаты поиска

Содержание Paper Deck Unit-F1

Отзывы:

Похожие инструкции для Paper Deck Unit-F1

Бренды по названию

Популярные бренды

Canon Paper Deck Unit-F1, Руководство по обслуживанию

Результаты поиска

Содержание Paper Deck Unit-F1

Отзывы:

Похожие инструкции для Paper Deck Unit-F1

Бренды по названию

Популярные бренды