Canon iPF720 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя

Страница: 80 / 204

Chapter 2

2-24

Cleaning operation timings are as follows.

Printer status

Cleaning operation

Consumption

(typ.)*1

Standby

168 hours elapsed capped

Cleaning 1 (Normal
Cleaning)

At least 720 to 960 hours elapsed since the last session of Cleaning 2, 3, 6 or 10 (480 hours after
initial installation)

Cleaning 6 (Normal
(strong) Cleaning)

At initial installation and 96 hours elapsed since the last session of Cleaning 16

Cleaning 16
(Precipitated ink
agitation)

1 hour elapsed capped with a specified number of dots discharged per chip completed after last
wiping

Idle ejection

0.013g

Power-on

At initial installation

Cleaning 3 (initial filling
ink)

15g

Both heads and inks
available

The print operation has completed. 168 to 720 hours elapsed capped

Cleaning 1 (Normal
Cleaning)

At least 720 to 960 hours elapsed
since the last session of Cleaning 2,
3, 6 or 10 (360 to 480 hours after
initial installation)

Cleaning 6 (Normal
(strong) Cleaning)

At least 960 to 2160 hours elapsed
since the last session of Cleaning 2,
3, 6 or 10 (480 hours after initial
installation)

Cleaning 2 (Ink level
adjustment and
cleaning)

10g

At least 96 hours elapsed since the
last session of Cleaning 16

Cleaning 16
(Precipitated ink
agitation)

At least 1 hour elapsed capped with
a specified number of dots
discharged per chip completed after
last wiping

Idle ejection

0.013g

Print operation aborted (uncapped)
and CR error occurring

Up to 72 hours elapsed after an
abort

Cleaning 1 (Normal
Cleaning)

Over 72 hours elapsed after an abort Cleaning 6 (Normal

(strong) Cleaning)

Print operation aborted (uncapped) and no CR error occurring

Cleaning 11 (ink filling
after head replacement)

10g

No heads are available

Cleaning 10 (ink filling
on secondary transport)

15g

Power off

Specified number of dots discharged per chip completed since the last session of wiping

Idle ejection

0.013g

Before the
start of
printing

Less than 168 hours elapsed capped

Idle ejection

0.013g

At least 168 hours elapsed capped

Cleaning 1 (Normal
Cleaning)

Before printing in the wake of an error occurrence

Cleaning 1 (Normal
Cleaning)

Printing

Before scanning while printing

Idle ejection (+Wiping)

- (0.013g)

After the end
of printing

A specified number of dots (color) discharged per chip since the last session of Cleaning 2, 3, 6 or 1 Cleaning 6 (Normal

(strong) Cleaning)

A specified number of dots discharged per chip after the last session of wiping

Idle ejection

0.013g

3 minutes elapsed since the last session of capping

Idle ejection

0.013g

Total 2 hours elapsed uncapped since the last session of Cleaning 1, 2, 3, 6 or 10

Cleaning 1 (Normal
Cleaning)

When the
Head
Cleaning
menu choice
is executed

Manual Cleaning (Head Cleaning A)

Cleaning 1 (Normal
Cleaning)

Manual cleaning (Head cleaning B)

Cleaning 6 (Normal
(strong) Cleaning)

When the
Replace Print
Head menu
choice is
executed

After head replacement

Cleaning 2 (ink level
adjustment and
cleaning) + Cleaning 4
(ink drainage for head
replacement)

10g

When the
Move Printer
menu choice
is executed

After the Move Printer menu choice is executed

Cleaning 5 (ink drainage
for secondary transport)

10g

After power-on at secondary installation

After power-on at
secondary installation

15g

*1: Quantities of ink consumption by nozzle train

Содержание iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Результаты поиска

Содержание iPF720 - imagePROGRAF Color Inkjet Printer

Отзывы:

Похожие инструкции для iPF720 - imagePROGRAF Color Inkjet Printer

Бренды по названию

Популярные бренды

Canon iPF720 - imagePROGRAF Color Inkjet Printer, Руководство по обслуживанию

Результаты поиска

Содержание iPF720 - imagePROGRAF Color Inkjet Printer

Отзывы:

Похожие инструкции для iPF720 - imagePROGRAF Color Inkjet Printer

Бренды по названию

Популярные бренды