Canon iPF720 - imagePROGRAF Color Inkjet Printer Скачать руководство пользователя | Manualshive

Страница: 198 / 204

background image

Chapter 8

8-4

Cannot adjust eccentric.

Press Online to clear the error.

03010000-2822

Eccentricity correction disabled

Check to see if paper has not jammed.

Sheet printing is selected.

Press Load/Eject and load sheets.

03860002-2E02

Data with a cut sheet specification has been
received but no cut sheets are loaded.

Load cut sheets at the paper tray port.

Roll printing is selected, but sheets
are loaded.

Press OK, remove the sheets, and
load a roll.

03860002-2E0A

Data with a roll media specification has
been received when a cut sheet tray is
loaded.

Replace with roll media.

Roll printing is selected.

Press Load/Eject and load a roll.

03060A00-2E00

Data with a roll media specification has
been received but no roll media are loaded.

Load roll media.

No Roll Feed Unit.

Turn printer off and install roll
feed unit.

03060A00-2E0E

Roll media unit not installed

Install the roll media unit.

The roll is empty.

Lift the release lever and replace
the roll.

03060A00-2E1B

Roll media end

Renew the supply of roll media.

Wrong paper feed slot for this
paper type.

Press Load/Eject and reload the
paper.

03061000-2E15

Paper type mismatch

Check the type of paper that can be fed and reload the
paper.

Manual printing is selected, but a
roll is loaded.

Press Load/Eject and remove the
roll.

03860001-2E0C

Data with a cut sheet specification has been
received when roll media are loaded.

Load cut sheets at the paper tray port.

Hardware error.
03130031-291D

Turn off printer, wait, then turn on
again.

03130031-291D

Spur cam sensor detection failure

Check the spur cam sensor.

Hardware error.
03130031-2E23

Turn off printer, wait, then turn on
again.

03130031-2E23

Cutter unit failure

Check the cutter unit.

Hardware error.
03130031-2E14

Turn off printer, wait, then turn on
again.

03130031-2F14

Writing to the ASIC register disabled

Replace the main controller PCB

Hardware error.
03130031-2E16

Turn off printer, wait, then turn on
again.

03130031-2F16

Mist fan error

Check the mist fan.

Hardware error.
03130031-2E17

Turn off printer, wait, then turn on
again.

03130031-2F17

Suction fan lock detection error

Check the suction fan.

Hardware error.
03130031-2E20

Turn off printer, wait, then turn on
again.

03130031-2F20

Purge motor cam position error

Check the purge unit.

Hardware error.
03130031-2E22

Turn off printer, wait, then turn on
again.

03130031-2F22

Pump travel timeout

Check the purge unit.

Hardware error.
03130031-2E23

Turn off printer, wait, then turn on
again.

03130031-2F23

Purge motor error
Pump inoperable

Check the purge unit.

Hardware error.
03130031-2E25

Turn off printer, wait, then turn on
again.

03130031-2F25

Unable to detect the carriage motor home
position

Check the carriage unit. Check the linear encoder for
smears.

Hardware error.
03130031-2E26

Turn off printer, wait, then turn on
again.

03130031-2F26

Carriage inoperable

Check the carriage unit and surrounding parts.

Display massage

Code*

Condition detected

Action

«
...
196
197
198
199
200
...
»

Содержание iPF720 - imagePROGRAF Color Inkjet Printer













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для iPF720 - imagePROGRAF Color Inkjet Printer

Бренд: GRAPHTEC Страницы: 4

Бренд: Oce Страницы: 132

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды