Canon imagePROGRAF iPF815, Руководство по обслуживанию

Страница: 308 / 324

Chapter 8
8-30
2F47 Hardware error.
3800500-2F47
Turn off printer,wait, then
turn on again. Only for iPF750 series The optical axis of the head management
sensor unit has been intercepted for some
reasons.
The amount of LED luminescence and the
level of detection signal of diode light
receiving sensitivity has gone beyond the
predefined range. (determines the level of
APCCHK)(It's not a problem of printhead
or ink supply system.)
1. Check whether any foreign matter
such as paper slip exists on the head
management sensor optical axis.
2. Light interception due to ink
accumulation.-> Remove the ink/
Replace the unit.
3. Check connection of the head
management sensor's connector.
4. Main controller PCB (Check the
fuse/ Replace the PCB.)
5. A large amount of ink mist has been
attached to optical element.
6. Replace the head management
sensor.
2F48 Hardware error.
03130031-2F48
Turn off printer, wait, then
turn on again. VHT (heater drive drive power supply for
printhead) error
VHT has gone below or above the rating. iPF6300 series
1. Replace the printhead.
2. Replace the main controller PCB.
iPF8300 series
1. Replace the printhead.
2. Replace the CR relay board.
3. Check/ replace the long flexible
cable.
4. Replace the main controller PCB.
2F49
2F50
2F51 Hardware error.
03130031-xxxx
Turn off printer, wait, then
turn on again. Printhead short-circuited detected.
Prior to VH power on, it has been detected
that the printhead had been damaged due to
paper jam etc, and ink went inside the
terminal area causing near short-circuit.
2F49: L side printhead
2F50: R side printhead
2F51: LR both printhead iPF6300 series
1. Replace the printhead
2. Replace the main controller PCB.
iPF8300 series
1. Replace the printhead
2. Replace the CR relay board
3. Check/ replace the long flexible
cable.
4. Replace the main controller PCB.
2F4A Hardware error.
03130031-2F4A
Turn off printer, wait, then
turn on again. iPF6300/830 or newer main controller PCB error. Replace the main controller PCB.
2F4D Hardware error.
03130031-2F4D
Turn off printer, wait, then
turn on again. Left printhead only.
Possible to occur on
iPFX400 or newer models.
VHT leak detection error of left printhead,
in case of VHT exceeds rated value or falls
below the rated value. For iPF6400 series,
1. Replace the printhead.
2. Replace the main controller PCB.
For iPF8400/9400 series,
1. Replace the printhead.
2. Replace the CR relay board.
3. Check and replace the long flexible
cable printed circuit.
4. Replace the main controller PCB.
2F4E Hardware error.
03130031-2F4E
Turn off printer, wait, then
turn on again. Right printhead or a single
printhead
Possible to occur on
iPFX400 or newer models.
VHT leak detection error of right
printhead, in case of VHT exceeds rated
value or falls below the rated value.
2F4F Hardware error.
03130031-2F4F
Turn off printer, wait, then
turn on again. Possible to occur on
iPFX400 or newer models. VHT leak detection error of right and left
printhead or a single printhead, in case of
VHT exceeds rated value or falls below the
rated value.
2F52 Hardware error.
03130031-2F52
Turn off printer, wait, then
turn on again. Detected that a carriage unit of a legacy
model has been mounted (iPF8300/6300/
6350 only). Replace with an appropriate carriage
unit.
1. Replace with an appropriate carriage
unit.
2. Replace the printhead.
3. Replace the main controller PCB.
2F53 Hardware error.
03130031-2F53.
Turn off printer,wait, then
turn on again. Supply valve motor error of the left ink
tank.
Drove supply valve motor. The movement
was not detected. iPF8400/9400 Series
1. Replace the left ink tank unit.
2. Replace the main controller PCB.
2F54 Hardware error.
03130031-2F54.
Turn off printer,wait, then
turn on again. Supply valve motor error of the right ink
tank.
Drove supply valve motor. The movement
was not detected. iPF8400/9400 Series
1. Replace the right ink tank unit.
2. Replace the main controller PCB.
2F60 !Spectrophotometer Unit
not connected.
Turn off power and attach
Spectrophotometer Unit. Spectrophotometer unit won't return
signals. 1. Install spectrophotometer unit.
2. Replace signal line.
3. Replace connection.
4. Replace spectrophotometer unit
PCB.
2F61 Hardware error
038A0002-2F61
Turn off printer, wait a
while, then turn it on again. UART communication error.
(Data transfer volume in consistency,
checksum error etc.) 1. Replace signal line.
2. Replace connection.
3. Replace spectrophotometer unit
PCB
2F62 Hardware error
038A0002-2F62
Turn off printer, wait a
while, then turn it on again. When transmitting specified pulses to
spectrophotometer carriage motor, the
spectrophotometer carriage unit won't
respond to spectrophotometer carriage HP
sensor. 1. Replace spectrophotometer unit
PCB.
2. Replace lines around
spectrophotometer carriage unit.
3. Replace spectrophotometer carriage
motor.
Code
(last 4 digits)
Panel display
(Large LCD)
Panel display
(Small LCD)
Explanation/Detection sequence Remedial Action