Canon imagePROGRAF iPF815, Руководство по обслуживанию

Страница: 284 / 324

Chapter 8
8-6
1400
to
140C No ink left.
Press OK and
replace ink tank. Ink tank empty (continued use allowed)
The ink tank has run out of ink, but a
certain volume of ink is reserved in the
subtank. (The reserved volume of ink is put
to use after the remaining ink falls below
the pin check level.)
Displayed only on models having a
subtank.
(XX: Display applicable colors)
Last 2 digits: 00:Bk, 01:Y, 02:M, 03:C,
04:PM, 05:PC, 06:MBk1, 07:MBk2,
08:GY, 09:PGY, 0A:R, 0B:B, 0C:G 1. Replace the tank.
2. Failure of remaining ink detection
system.
(Replace the supply unit /check the
bundled wires.)
Ink tank is empty.
Replace the ink
tank.
1410
to
141C No ink tank
loaded.
Check ink tank. Ink tank not installed (continued use
allowed)
The ink tank is not installed but a sufficient
volume of ink is left in the subtank.
Displayed only on models having a
subtank.
This occurs in cases such as when the ink
tank cover is opened during printing, and
the ink tank is removed. (XX: Displays
applicable colors)
Last 2 digits: 10:Bk, 11:Y, 12:M, 13:C,
14:PM, 15:PC, 16:MBk1, 17:MBk2,
18:GY, 19:PGY, 1A:R, 1B:B, 1C:G 1. Mount the tank.
2. Failure of remaining ink detection
system.
(Replace the supply unit /check the
bundled wires.)
200A Paper size not
detected. Press Load/Eject
and reload the
paper. Paper
Please Reload
Size Undetected Paper size detection failure
Cannot detect the paper width (poorly
positioned paper).
Paper size not
detected. Reload paper.
Paper size not
detected. Press OK and
reload the paper.
200B Paper size not
detected. Reload paper. Paper
Please Reload
Size Undetected Paper size detection failure
Paper is invalidly positioned on the platen.
200C Paper size not
detected.
Press Load/Eject
and reload the
paper. Paper
Please Reload
Size Undetected Paper size detection failure
Cannot detect the leading edge of the
paper.
The leading edge of paper has been located
by coarse detection but not by a second
round of fine detection (up to 300 mm)
(semi-transparent paper).
(This is the message when the release lever
operation is not necessary.)
Paper size not
detected.
Reload paper.
Paper size not
detected.
Lift the release
lever and reload
the paper. Papr Size
Undetected
Press Online Key
and Reload Paper size detection failure
Cannot detect the leading edge of the
paper.
The leading edge of paper has been located
by coarse detection but not by a second
round of fine detection (up to 300 mm)
(semi-transparent paper).
200D Paper size not
detected.
Press Load/Eject
and reload the
paper. Paper
Please Reload
Size Undetected Paper size detection failure
Cannot detect the trailing edge of the paper.
-Cannot detect the trailing edge of the cut
sheet loaded after they have been fed 50
mm.
-Cannot locate the trailing edge of the
paper that has been found by coarse
detection. 1. Check to see if roll paper are not
loaded in the cut sheet mode.
2. Load cut sheet.
Leading edge
detection error.
Lift the release
lever and align
leading edge
with orange line.
Paper size not
detected.
Lift the release
lever and reload
the paper.
Paper size not
detected.
Reload paper.
200E This paper
cannot be used.
Check supported
paper sizes. Paper Size
Please Check
Paper Too Small Paper is too small
The width and length of paper detected are
shorter than the supported size (1.5%
margin). 1. Check paper conditions (soiling,
tear-offs, residual paper chips, residual
trimming cuts, folds)/size.
2. Has the paper been fed successfully
(without slippage under a load or any
influence)?
3. Has the LF adjustment value set
correctly?
4. Hasn't the loaded paper shrunk to
below its margin in the particular
environment?
This paper
cannot be used.
Check supported
paper sizes.
Load/Eject: Change Paper Paper Size
Please Check
Paper Too Small
Press Online Key
Code
(last 4 digits)
Panel display
(Large LCD)
Panel display
(Small LCD)
Explanation/Detection sequence Remedial Action