Canon imagePRESS C1 P, Руководство по обслуживанию, Страница: 891 / 1265

Chapter 15
15-28
0049 1st sheet delivery stationary
2 PI13,S9 When delivery stationary 2 (0009) occurs on the 1st sheet.
0050 1st sheet pre-reverse delay 1 S3 When pre-reverse delay 1 (0010) occurs on the 1st sheet.
0051 1st sheet pre-reverse delay 2 S1,S3 When pre-reverse delay 2 (0011) occurs on the 1st sheet.
0052 1st sheet pre-reverse delay 3 PI4 When pre-reverse delay 3 (0012) occurs on the 1st sheet.
0053 1st sheet pre-reverse
stationary 1 S1,S4 When pre-reverse stationary 1 (0013) occurs on the 1st sheet.
0054 1st sheet pre-reverse
stationary 2 S2,S4 When pre-reverse stationary 2 (0014) occurs on the 1st sheet.
0055 1st sheet pre-reverse
stationary 3 S2,S3 When pre-reverse stationary 3 (0015) occurs on the 1st sheet.
0056 1st sheet pre-reverse
stationary 4 S1,S3 When pre-reverse stationary 4 (0016) occurs on the 1st sheet.
0057 1st sheet pre-reverse pickup
delay S1 When pre-reverse pickup delay (0017) occurs on the 1st sheet.
0058 1st sheet pre-reverse pickup
stationary 1 S1,PI4 When pre-reverse pickup stationary 1 (0018) occurs on the 1st sheet.
0059 1st sheet pre-reverse pickup
stationary 22 S1,PI4 When pre-reverse pickup stationary 2 (0019) occurs on the 1st sheet.
0060 1st sheet reverse pickup
delay S2 When reverse pickup delay (0020) occurs on the 1st sheet.
0061 1st sheet reverse pickup
stationary S2 When reverse pickup stationary (0021) occurs on the 1st sheet.
0062 1st sheet pickup leading edge
skew S4,S5 When pickup leading edge skew (0022) occurs on the 1st sheet.
0063 1st sheet pickup trailing edge
skew S4,S5 When pickup trailing edge skew (0023) occurs on the 1st sheet.
0064 1st sheet pickup NG 1 S1 When pickup NG 1 (0024) occurs on the 1st sheet.
0065 1st sheet pickup NG 2 S3,S2 When pickup NG 2 (0025) occurs on the 1st sheet.
0066 1st sheet reverse pickup
trailing edge skew S4,S5 When reverse pickup trailing edge skew (0026) occurs on the 1st sheet.
0067 1st sheet reverse pickup NG
1 PI4 When reverse pickup NG 1 (0027) occurs on the 1st sheet.
0071 Timing error 1 - Beyond control of software
0072 Timing error 2 - When a previous document has yet to be delivered while a scanned document is moved to the right side
of the platen roller during the fixed reading.
0073 Illegal size S3 When the registration roller rear sensor detects a document after it is fed by a specified amount (30mm)
from the waiting position during the LDR stream reading.
0074 Manual feed document size
error S9,S1 When the reverse sensor detects a document while the multifeed registration roller sensor is detecting it
during the multifeed pickup operation.
0075 Image start position error S7 When the reading position is not changed in response to a reading position change request during the
stream reading.
0076 1st sheet image start position
error S7 When image start position error (0075) occurs on the 1st sheet.
0077 Belt speed setting error PI1 When the specified speed of the belt motor is less than the minimum speed (100 mm/s) or more than the
maximum speed (700 mm/s).
0078 Belt speed switch error PI1 When the belt motor is not in the normal speed when the belt motor speed is switched.
0079 Belt status error PI1 When the belt motor status is not any of acceleration, normal, or deceleration when it is switched.
0080 Image start position output
timing error S2,S3,SW301 When the image start position signal is output during acceleration while a document is fed from the
waiting position to the image start position during the stream reading.
0081 Reverse speed setting error PI5 When the specified speed of the reverse motor is less than the minimum speed (100 mm/s) or more than
the maximum speed (700 mm/s).
0082 Reverse speed switch error PI5 When the reverse motor is not in the normal speed when the reverse motor speed is switched.
0083 Reverse status error PI5 When the reverse motor status is not any of acceleration, normal, or deceleration when it is switched.
0084 Last document error PI1 A belt motor error occurs while a last document is being delivered or moved from the platen roller.
0085 Error PI1,PI2,PI11 When a motor error other than IPC communication/ pickup error occurs. (less than three times)
0090 ADF open PI10 When opening of the ADF is detected.
0091 User ADF open PI10 When opening of the ADF is detected while the machine is in operation.
0092 Cover open PI3,PI6 When opening of a cover (front or rear) is detected.
Code Type of Jam Sensor No. Details