Canon imagePASS-A2 Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 82

background image

T

ROUBLESHOOTING

77

Printing to the imagePASS

If the customer can print the imagePASS Test Page but cannot print a job from a computer on
the network, you may have to make a service call. However, first make sure that the site
administrator has done the following:

• Checked all components of the network, including cables, connectors, terminators,

network adapter boards, and network drivers.

• Activated the network and used it to communicate with other printers.

• Confirmed that the applicable network settings in Setup (such as AppleTalk zone,

IP address, subnet mask, and gateway address) match the settings used in the network.

When you make a service call, check the imagePASS connector panel to make sure that the
appropriate network connection is in place. Print quality problems are difficult to trace.
Before you try to troubleshoot print quality problems, print a Test Page to make sure that the
copier does not need servicing or adjusting. Also, make sure that the correct paper is being
used in the copier.

N

OTE

:

EPS file generation is not completely standardized among applications. Some users

may encounter problems while printing certain EPS files.

If the printer does not print

The following table lists possible causes and solutions when the printer does not print.

T

ABLE

2:

Causes and solutions when printer does not print

Possible Cause

Solution

Is the power on?

• Press and hold the power button on the imagePASS to turn it on and/or when the imagePASS is

ready, power on the copier.

Are the cables between the
imagePASS and the copier
connected?

• Make sure that the copier interface cables are completely and correctly connected to the copier and

the imagePASS.

Is the specified paper loaded?

• Load the specified paper in any of the input trays.

Can you print a Test Page from
the printer driver?

• If you cannot print the Test Page, the copier may be out of order. You may need to service the

copier.

Is the enclosed fan present and
functioning?

• Verify that the enclosed fan is present, oriented correctly, and functioning (see

«
...
75
76
77
78
79
...
»

Содержание imagePASS-A2



















































































Отзывы:

Нет отзывов

Похожие инструкции для imagePASS-A2

ImageCLASS MF4570dw

Бренд: Canon Страницы: 164

imagePRESS C800 Series

Бренд: Canon Страницы: 132

ImageCLASS MF5730

Бренд: Canon Страницы: 2

JG Titan MKII V2

Бренд: iBox Страницы: 5

Бренд: Xerox Страницы: 2

Бренд: BIXOLON Страницы: 29

Бренд: Zonestar Страницы: 25

Бренд: Oki Страницы: 255

PG 2028 SPECIAL

Бренд: Olivetti Страницы: 104

Бренд: Microcom Страницы: 73

Бренд: Keithley Страницы: 97

Бренд: Lexmark Страницы: 142

Бренд: Microcom Страницы: 207

Бренд: Creality Страницы: 24

invitrogen EVOS FL

Бренд: Thermo Scientific Страницы: 6

Бренд: Lexmark Страницы: 2

Бренд: Konica Minolta Страницы: 28

Бренд: Oki Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды