Canon imagePASS-A2 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 82

background image

S

YSTEM

S

OFTWARE

51

S

YSTEM

S

OFTWARE

This chapter includes the following topics:

•

“System software installation reminders”

•

“Installing system software through an Ethernet port”

•

“Installing system software through a USB flash drive”

•

“Installing software updates”

•

“System software installation error messages”

System software installation reminders

When you install system software, keep the following in mind:

•

Fonts

Installing system software deletes all fonts that the customer has installed on the
imagePASS. Only resident fonts are restored during system software installation. You can
use Downloader to reinstall additional fonts.

To determine which additional fonts were downloaded to the imagePASS, print the Font
List before you format the hard disk drive, and again after you complete the system
software installation. Any fonts not listed after installation must be reinstalled. For more
information, see

Utilities

, which is part of the user documentation set.

•

Language

Screens for installing system software are always displayed in English, even if the copier is
configured for another language.

•

Compatibility

The latest user software must be installed on all computers that print to the imagePASS.
Using incompatible versions of the system and user software may result in system
problems.

Backing up the system configuration

If you back up the system configuration, you can restore it after you reinstall system software.
When you back up the system configuration, you save a configuration file with imagePASS
settings.

If you cannot create a configuration file, ask the network administrator to archive custom
color profiles, preflight templates, FreeForm masters, custom Paper Catalog entries,
customer-installed fonts, and the Job Log to removable media or a network location.

«
...
49
50
51
52
53
...
»

Содержание imagePASS-A2



















































































Отзывы:

Нет отзывов

Похожие инструкции для imagePASS-A2

Бренд: WaxJet Страницы: 131

Бренд: Datamax Страницы: 2

Бренд: G3D Страницы: 4

Бренд: TallyGenicom Страницы: 3

Бренд: VASTEX Страницы: 15

Бренд: Grizzly Страницы: 56

ApeoSport C5540I

Бренд: Fuji Xerox Страницы: 108

Multi-Font NX-2415

Бренд: Star Micronics Страницы: 134

Fast T-Jet Blazer Pro

Бренд: Screen Print & Inkjet Страницы: 138

Бренд: VASTEX Страницы: 8

Бренд: Brady Страницы: 48

Бренд: DPM Страницы: 2

DLQ-3000 Minerva+

Бренд: Epson Страницы: 189

Бренд: Epson Страницы: 223

Бренд: Epson Страницы: 228

DFX-8500 - Impact Printer

Бренд: Epson Страницы: 245

Бренд: Epson Страницы: 262

Disc producer PP-100N Security

Бренд: Epson Страницы: 153

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды