Canon imagePASS-A2 Скачать руководство пользователя страница 42

Страница: 42 / 82

ERVICE

ROCEDURES

Enclosed fan

The enclosed fan is located inside the chassis and cools the system. An arrow on the enclosed
fan indicates what direction air flows out.

When you install the enclosed fan, you make sure that it is facing the correct direction, so that
air blows out of the imagePASS. Failure to do so may result in future damage to the
imagePASS

IGURE

18:

Enclosed fan

REMOVE

THE

ENCLOSED

FAN

When you handle electronic components, follow electrostatic discharge (ESD) precautions
(see

page 10

1 Note the orientation of the fan and the arrow indicating the air flow out of the vent.

Tip

: The air flows

towards

the side of the fan that has the fan label.

2 Remove and set aside the fan rivets; remove the fan.

Tip

: Insert a short tool less than 4.4 mm in diameter into each access hole, find the center of

the rivet, and push the rivet out. Or, pry the cap of the rivet up with a thin, dull blade.

3 Transfer the fan guard (if installed) from the old fan to the correct side of the new fan, using

the guard rivets. Note that guard rivets may differ significantly from fan rivets.

Rivet

Содержание imagePASS-A2



















































































Результаты поиска

Содержание imagePASS-A2

Отзывы:

Похожие инструкции для imagePASS-A2

Бренды по названию

Популярные бренды

Canon imagePASS-A2, Руководство по обслуживанию

Результаты поиска

Содержание imagePASS-A2

Отзывы:

Похожие инструкции для imagePASS-A2

Бренды по названию

Популярные бренды