Canon ImageCLASS MF4690 Скачать руководство пользователя страница 169 | Manualshive

Страница: 169 / 182

background image

Chapter 14

14-29

of the signals from the speaker with the sounds from a normal modem.
End this test by pressing the Stop key.

Relay Test

Press '1'or '2' on the keypad on the Modem test menu to select relay test mode. Use the keypad to operate the various relays of the NCU. '2' on the keypad is used
for 230V machine.
Numeric keypad key 1
The input key and relay are shown below:

F-14-9

Numeric keypad key 2
The input key and relay are shown below:

F-14-10

The touch panel (LCD) is turned on or off in relation to the transmission of the relay operation signal as is operated on the keypad; for this reason, you cannot use
the touch panel (LCD) to check a fault on a single relay.

Frequency Test

A press on '2' on the keypad from the MODEM test menu selects the frequency test.
In this test, signals of the following frequencies from the modem are transmitted using the telephone line terminal and the speaker. To select a different frequency,
use the keypad.

MEMO:

The frequency and the output level of individual frequencies are in keeping with the output level set in service mode.

Keypad

Type

Description

1

Relay test

Use it to turn on/off a selected relay to execute a switch-over test

2

Frequency test

The modem sends tonal signals from the modular jack and the speaker.

4

G3 signal transmission test

The modem sends G3 signals from the modular jack and the speaker.

5

DTMF signal reception test

Use it to generate the DTMF signal coming from the modem using the
telephone line terminal and the speaker.

6

Tonal signal reception test

Use it to monitor a specific frequency and the DTMF signal received from
the telephone line terminal by causing them to be indicated on the LCD (i.e.,
the presence/absence as detected). The reception signal is generated by the
speaker.

8

V.34 G3 signal transmission test

The modem sends V.34 G3 signals from the modular jack and the speaker.

Keypad

Frequency

0

462Hz

1

1100Hz

2

1300Hz

3

1500Hz

4

1650Hz

5

1850Hz

6

2100Hz

RELAY TEST1 OFF OFF
OFF OFF OFF OFF

[1]

[2]

[3]

[4]

[5]

[6]

RELAY TEST2 OFF OFF
OFF OFF OFF OFF OFF

[1]

[2]

[3]

[4]

[5]

[6]

[7]

«
...
167
168
169
170
171
...
»

Содержание ImageCLASS MF4690























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCLASS MF4690

Бренд: DataCard Страницы: 7

Бренд: TE Connectivity Страницы: 2

Бренд: TE Connectivity Страницы: 2

7760DN - Phaser Color Laser Printer

Бренд: Xerox Страницы: 6

MAGICARD 300plus

Бренд: Ultra electronics Страницы: 45

WorkCentre PRO 35

Бренд: Xerox Страницы: 13

Document Centre 255 LP

Бренд: Xerox Страницы: 158

tecjet 6090DTG-dx5

Бренд: TEC Страницы: 73

Бренд: SAGEMCOM Страницы: 146

Бренд: RHINO Страницы: 21

Бренд: Ricoh Страницы: 678

Accel-a-Writer 4

Бренд: Xante Страницы: 12

Бренд: Compaq Страницы: 238

Бренд: IBM Страницы: 128

Бренд: OmniPrint Страницы: 71

1000 Color Jetprinter

Бренд: Lexmark Страницы: 56

Бренд: IBM Страницы: 2

3210 - workcentre b/w laser

Бренд: Xerox Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды