Canon ImageCLASS MF4690 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 182

background image

Chapter 14

14-20

Bit 6 details
Select whether to enable the host machine to work as a USB storage device or not. If the host machine is plugged into a PC with this setting enabled, it allows user
registration data (user data and telephone registration data) to be imported and exported to and from the PC, except for the data embedded in the department man-
agement information and user management IDs in the system management information.

14.9 Counter Indication (COUNTER)

14.9.1 Counters

0016-2108

This copier is furnished with a maintenance/supplies counter set (DRBL-1), which can be used to gain rough measures of when to replace supplies. The counter
set increments by one on counting each sheet of small-sized paper (up to A4/LTR) and by two on counting each sheet of large-sized paper (larger than A4/LTR).

T-14-19

14.9.2 Clearing Counters

0016-2110

- Maintenance counter all clear
Execute service mode > CLEAR > COUNTER to clear all maintenance counters.

2

Not used

-

-

3

Not used

-

-

4

Not used

-

-

5

Not used

-

-

6

Imports and exports user information via USB.

Enable

Disable

7

Not used

-

-

Maintenance counter list

Item

Counter

Explanation

TOTAL (Total counter)

SERVICE1

Service total counter 1

SERVICE2

Service total counter 2

TTL

Total counter

COPY

Total copy counter

PDL-PRT

PDL print counter

FAX-PRT

Fax print counter

RPT-PRT

Report print counter

2-SIDE

Double-sided copy/print counter

SCAN

Scan counter

PICK-UP (Paper pickup counter)

C1

Cassette jam counter

C2

Not used

C3

Not used

C4

Not used

MF

Multi-purpose tray pickup total counter

2-SIDE

Double-sided paper pickup total counter

FEEDER (Feeder related counters)

FEED

ADF pickup total counter

DFOP-CNT

Not used

JAM (Jam counters)

TTL

Unit total jam count

FEEDER

ADF total jam count

SORTER

Not used

2-SIDE

Duplex unit jam counter

MF

Multi-purpose tray jam counter

C1

Cassette jam counter

C2

Not used

C3

Not used

C4

Not used

MISC (Other required counter)

WST-TNR

Not used

Bit

Function

1

0

«
...
158
159
160
161
162
...
»

Содержание ImageCLASS MF4690























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCLASS MF4690

Бренд: NCR Страницы: 10

Бренд: EBS Страницы: 4

Бренд: NCR Страницы: 38

Бренд: LabelTac Страницы: 2

Бренд: Xerox Страницы: 9

Бренд: Xerox Страницы: 2

Бренд: Xerox Страницы: 8

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 150

Бренд: Xerox Страницы: 4

Бренд: Xerox Страницы: 6

Бренд: Xerox Страницы: 2

DocuPrint N2125

Бренд: Xerox Страницы: 246

DocuPrint N2025

Бренд: Xerox Страницы: 378

DocuPrint N2025

Бренд: Xerox Страницы: 176

DocuPrint C3290 FS

Бренд: Xerox Страницы: 240

Бренд: Xerox Страницы: 5

Бренд: Xerox Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды