Canon ImageCLASS MF4690 Скачать руководство пользователя страница 132

Страница: 132 / 182

Chapter 13

13-2

The following are the error codes used in the image transmission function with network.

T-13-2

E736

0000

CCU communication error

The installed modem PCB is incompatible.

- Check the connectors of the image processor PCB and modem.
- Replace the modem PCB.
- Replace the image processor PCB.

E739

0000

Erroneous communication between controller and network board

The installed network board is incompatible.

- Check the connectors of the image processor PCB and LAN
PCB for normal connection.
- Replace the LAN PCB.
- Replace the image processor PCB.

E805

0000

Fan failure

The fan is faulty.

- Check the fan connector.
- Replace the fan.
- Replace the DC controller PCB.

E808

0000

Fixing drive circuit failure

- The heater does not turn on.
- A fixing drive motor failure was detected.

- Check the connector of the fixing film unit.
- Replace the fixing film unit.
- Replace the fixing drive motor.
- Replace the DC controller PCB.
- Replace the power supply PCB.

Error
Code

Send

Recive

Error detail

SMTP

FTP

SMB

SMTP

POP3

#705

Yes

Exceeded max. image size per document
Exceeded max number of image pages (100 pages) in PDF transmission

#751

Yes

Failed to connect to server (Socket level)
Disconnected the network (Socket is closed.)

#752

Yes

Failed to connect to server (Socket level)
Disconnected the network (Socket is closed.)

#753

Yes

Occurred socket errors other than E751/E752

#755

Yes

It started beginning to transmit before the network was connected.

#801

Yes

Returned error from SMTP server
SMTP protocol time out
Exceeded the specified connecting time limit.

#802

Yes

Failed in name resolution using DNS server

#804

Yes

Returned error from FTP server (No access right to the folder)

#806

Yes

Returned error from FTP server (User name/Password)

#808

Yes

Returned error from FTP server (Other than E804/E806)
FTP protocol time out
Exceeded the specified connecting time limit.

#810

Yes

Returned error from POP3 server
POP3 protocol time out
Exceeded the specified connecting time limit.

#812

Yes

POP3 password error

#813

Yes

POP3 login name error

#819

Yes

MIME data error

#820

Yes

Base64/uuencode error

#821

Yes

TIFF analysis error

#827

Yes

non support MIME receive

#828

Yes

Type of HTML mail receive error

#829

Yes

Exceeded max receivable size

#839

Yes

SMTP AUTH authentication error(email and iFAX transmitt

Display
Code

Detail Code

Main Cause/Symptom

Countermeasure

Содержание ImageCLASS MF4690























































































































































































Результаты поиска

Содержание ImageCLASS MF4690

Отзывы:

Похожие инструкции для ImageCLASS MF4690

Бренды по названию

Популярные бренды

Canon ImageCLASS MF4690, Руководство по обслуживанию

Результаты поиска

Содержание ImageCLASS MF4690

Отзывы:

Похожие инструкции для ImageCLASS MF4690

Бренды по названию

Популярные бренды