Canon ImageCLASS MF4690 Скачать руководство пользователя страница 168 | Manualshive

Страница: 168 / 182

background image

Chapter 14

14-28

error appearing on the touch panel (LCD).

Numeric keypad key 2
Checks to see if data can be correctly read from all areas of D-RAM (SDRAM). If an error occurs making this check, the test is aborted, with an error appearing
on the touch panel (LCD).

F-14-7

14.13.3 Scan Test

14.13.3.1 Scan Test ((2) SCAN TEST)

0016-2129

Scan test ((2) SCAN TEST)

Press the numeric keypad key 2 on the test mode menu to select the SCAN test.
Press numeric keypad keys 1 during the SCAN test to carry out the individual tests described below.

Numeric keypad key 1
Corrects the LED output of the contact sensor and sets its parameters automatically. (AGC adjustment)

14.13.4 Print Test

14.13.4.1 Print Test ((3) PRINT TEST)

0016-2130

Print test ((3) PRINT TEST)

Press the numeric keypad key 3 on the test mode menu to select the print test.
Press numeric keypad keys 2 and 4 during the print test to generate test patterns as described below. Two kinds of service test patterns are available. Other test
patterns are reserved for factory/development purposes.

Numeric keypad key 2
(2) BLACK: All-black output
Numeric keypad key 4
(4) ENDURANCE: Black belt output

To cancel test printing, press the stop key.

F-14-8

14.13.5 Modem Test

14.13.5.1 MODEM Test ((4) MODEM TEST)

0016-2131

MODEM test((4) MODEM TEST)

These tests test modem and NCU transmission and reception. The modem tests check whether signals are sent correctly from the modem by comparing the sound

D-RAM

TEST

29696KB

D-RAM

TEST

29696KB

D-RAM

TEST

29696KB

complete

(error)

29696

29696

D-RAM

TEST

29696KB

[1] - [2]

D-RAM

TEST

29696KB

complete

(no error)

WRT= 33CC RD= 33EC
ADR= BF840201

Use it to make sure that the print

pattern does not have white lines

or uneven image.

Use it to make sure that the print

pattern does not have contraction/

elongation of an image or dirt/black

line.s

«
...
166
167
168
169
170
...
»

Содержание ImageCLASS MF4690























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCLASS MF4690

CLP 510N - Color Laser Printer

Бренд: Samsung Страницы: 270

Bixolon SRP-270

Бренд: Samsung Страницы: 13

SPP 2020 - Photo Printer - 20 Sheets

Бренд: Samsung Страницы: 81

Бренд: Samsung Страницы: 98

Бренд: Samsung Страницы: 6

Бренд: Samsung Страницы: 203

Бренд: Samsung Страницы: 264

Бренд: Samsung Страницы: 228

Бренд: Samsung Страницы: 211

Бренд: Samsung Страницы: 5

Бренд: Samsung Страницы: 92

Бренд: Samsung Страницы: 75

Бренд: Samsung Страницы: 11

Бренд: Samsung Страницы: 206

ML 3050 - B/W Laser Printer

Бренд: Samsung Страницы: 103

ML 3050 - B/W Laser Printer

Бренд: Samsung Страницы: 215

Бренд: Samsung Страницы: 2

CLP 510N - Color Laser Printer

Бренд: Samsung Страницы: 266

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды