Canon ImageCLASS MF4690 Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 182

background image

Chapter 9

9-4

Make sure to attach the link stopper [2] after attaching the right cover. If at-
taching the link stopper while attaching the printer cover, it may drop inside
the machine.

4) With the printer cover [1] opened, detach it upward.

F-9-15

9.3.7 Operation Panel Unit

9.3.7.1 Removing the Control Panel Unit

0016-4991

1) Remove the 4 screws [1] and the 2 claws [2].

F-9-16

2) Disconnect the connector [1], and remove the control panel unit [2].

F-9-17

9.3.8 SCNT Board

9.3.8.1 Preparation for Removing the SCNT Board

0016-4992

Outputting report

Before replacing the SCNT board, output and record the report for the
information such as the user setting and the setting of the service mode.
Service mode > REPORT
Initial setting/registration > Report setting > Report output

9.3.8.2 Removing the SCNT Board

0016-5001

1) Remove the front cover.
2) Remove the right cover.
3) Remove the left cover.
4) Remove the rear cover.
5) Remove the frame [1].

- 11 screws [2]

F-9-18

6) Remove the Analog processor PCB.
7) Remove the SCNT board [1].

- 9 connectors [2]
- 4 flatcables [3]
- 9 screws [4]

F-9-19

9.3.8.3 Actions At Replacing the SCNT Board

0016-5066

Outputting report

Before replacing the SCNT board, output and record the report for the
information such as the user setting and the setting of the service mode.
Service mode > REPORT
Initial setting/registration > Report setting > Report output
After replacing the SCNT board, enter the user data and the service data
according to the report.

Changing the jumper connector

When replacing the SCNT board, change the position of the jumper
connector to ON.
* The SCNT board is shipped with the jumper connector of the lithium
battery OFF.

9.3.9 DCNT Board

9.3.9.1 Preparation for Removing the DCNT Board

0016-5004

1) Remove the front cover.
2) Remove the right cover.
3) Remove the left cover.

9.3.9.2 Removing the DCNT Board

0016-5005

1) Remove the 2 guides [1] in the direction of the arrow.

«
...
100
101
102
103
104
...
»

Содержание ImageCLASS MF4690























































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ImageCLASS MF4690

Бренд: DataCard Страницы: 7

Бренд: BCS Страницы: 151

Бренд: Konica Minolta Страницы: 846

Aficio SP C240SF

Бренд: Ricoh Страницы: 14

Бренд: Hanin Страницы: 27

Бренд: Canon Страницы: 65

Бренд: Ricoh Страницы: 17

Бренд: Xerox Страницы: 3

Бренд: Xerox Страницы: 233

Бренд: Delta OHM Страницы: 28

Accel-a-Writer 8200

Бренд: Xante Страницы: 12

Бренд: Ricoh Страницы: 130

Бренд: Lexmark Страницы: 2

Бренд: Lexmark Страницы: 489

imagePRESS V1000

Бренд: Canon Страницы: 123

Бренд: LG Страницы: 33

Бренд: LG Страницы: 49

Pocket Photo PD221

Бренд: LG Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды