Canon CR-X300 Скачать руководство пользователя страница 15

Страница: 15 / 114

Internal connection diagram

(7)

LAN terminal

Terminal (RJ-45 connector) for network connections.

With PoE++ (Power over E+) capability, it is possible to provide power to the camera from the PoE++

supported hub which compile IEEE802.3bt Type 2 through a LAN cable.

Use an STP (shielded) type LAN cable with a length of 100 m or less and with a category 5e or more. Use a

category 5 or less cable may reduce the power supply capacity.

(8)

HDMI OUT terminal

Terminal for HDMI output. Take necessary measures to prevent the cable from coming off, such as using a

commercially available cable retaining part.

(9)

6G-

DI terminal

Output terminal (BNC connector) for uncompressed digital video and digital audio.

(10)

YNC terminal

Input terminal (BNC connector) for the external synchronization signal.

(11) Cable clamp

A cable clamp to prevent the power cable from coming off. Thread the cable to prevent it from coming off.

Note

• The camera does not have a power switch. Turn on/off the power by connecting/disconnecting the power cable or LAN cable or

using the switch of the device that supplies power.

• If power is supplied from both DC power and PoE++, power from DC power has a priority. If the power supply is stopped from DC

power while power is supplied from both DC power and PoE++, power supply to the camera will be stopped. In this case,
disconnect the LAN cable to stop power supply from PoE++, reconnect the cable and restart, and power will be supplied again.

Important

• Some PoE++ supported hubs can limit power usage on each port, however doing so may cause failure to operate correctly. In

this case, do not limit power usage on any port.

• Other PoE++ supported hubs can limit the total power consumption of each port, however using multiple ports doing so may fail

to operate correctly. Refer to the instruction manual of the PoE++ supported hub for use.

+3.3 V
10 kΩ

AUX IN (No.6)

AUX OUT (No.4)

GND (No.5)

AUX OUT (No.3)

0.1 μF

Input terminal

Output terminal

Internal controller

Содержание CR-X300



















































































































Результаты поиска

Содержание CR-X300

Отзывы:

Похожие инструкции для CR-X300

Бренды по названию

Популярные бренды

Canon CR-X300, Руководство пользователя

Результаты поиска

Содержание CR-X300

Отзывы:

Похожие инструкции для CR-X300

Бренды по названию

Популярные бренды