Canon CanoScan D1230UF Скачать руководство пользователя страница 8

Страница: 8 / 115

chapter 1

Before You Begin

Top Page

Glossary

Contents

Index

System Requirements

The hardware and software listed below is required to use ScanGear
CS-U.

Hardware

•

You can use following scanner with ScanGear CS-U: CanoScan
D1230U/D2400U.

•

IBM PC or its compatible on which Windows Me, Windows 98 or
Windows 2000 Professional can run

•

Memory (RAM) required is determined by your system:
32 MB (64 MB or more recommended)

•

10 MB of free disk space for ScanGear installation

•

Free disk space, at least 50 MB. The amount of space required
depends on the scanning area and the Color Mode or Resolution
settings (color images scanned at higher resolution require more
storage space).

Note

Before you scan an image, check the file size in the
status bar. You should have at least twice that amount
of free space available on the hard disk.

•

Minimum requirement for monitor: 800 x 600 resolution
(minimum), High Color (16 bit) or greater.

Содержание CanoScan D1230UF




















































































































Результаты поиска

Содержание CanoScan D1230UF

Отзывы:

Похожие инструкции для CanoScan D1230UF

Бренды по названию

Популярные бренды

Canon CanoScan D1230UF, Руководство пользователя

Результаты поиска

Содержание CanoScan D1230UF

Отзывы:

Похожие инструкции для CanoScan D1230UF

Бренды по названию

Популярные бренды