Cannon CT-2000 Скачать руководство пользователя | Manualshive

Страница: 23 / 54

background image

CANNON Instrument Company | Unpack & Assemble

15

Insert Viscometer Tubes/Thermometers

The top cover of the CT-2000 contains seven apertures, 51 mm (2”) in diameter, for the insertion of
viscometer tube holders. Two additional holes are provided for insertion of thermometers. Refer to
Figure 15.

Figure 15: CT-2000 Top View shown without Hole Covers

If necessary, remove the viscometer tube cover(s) from the top of the bath and carefully place the
viscometer tube(s), with the proper holder attached, into the bath through the aperture(s) in the
top cover. The viscometer tube should be inserted to a depth which ensures that the liquid under
test and/ or any timing marks are a minimum of 6 mm (¼") below the top level of the liquid.

Thermometer Immersion

Proper thermometer immersion is critical for viscosity measurements. Even a calibrated
thermometer will read incorrectly if it is not properly immersed in the bath. Total immersion
kinematic viscosity thermometers should be used with the bulb and only the mercury column (if
applicable) beneath the surface of the liquid, but with the emergent stem above the surface at
ambient temperatures.

Note:

Different thermometers have different immersion requirements. Refer to

the information included with your particular thermometer for specific
requirements.

Filling the Bath

After CT-2000 unit assembly is complete, fill the bath.

«
...
21
22
23
24
25
...
»

Содержание CT-2000























































Отзывы:

Нет отзывов

Похожие инструкции для CT-2000

Бренд: Parker Research Corp Страницы: 3

Бренд: S.I.T.A. Страницы: 32

Бренд: idiag Страницы: 12

Бренд: Abicor Binzel Страницы: 92

Бренд: LAWO Страницы: 459

Бренд: earline Страницы: 13

Бренд: h/p/cosmos Страницы: 81

Бренд: Konica Minolta Страницы: 32

Бренд: Kärcher Страницы: 88

Бренд: Parker Страницы: 64

Бренд: Parker Страницы: 40

Matrx Digital MDM

Бренд: Parker Страницы: 20

Бренд: Ironton Страницы: 6

Бренд: MAGSTIM Страницы: 86

Бренд: MadLab Страницы: 7

Бренд: Osram Страницы: 4

Бренд: Ekinex Страницы: 37

Бренд: HMS Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды