Cannon CT-2000 Скачать руководство пользователя | Manualshive

Страница: 27 / 54

background image

CANNON Instrument Company | Bath Operation

19

Warm Start

The Warm Start is the abnormal start-up mode for the bath and it occurs only if the power was
previously off for a period of less than about two seconds, or if a fault was detected in the
microprocessor during the

Self-Test Sequence

. If the CT-2000 Process Function Monitor senses a

momentary or ongoing failure in the system hardware and/or software, the heating elements are
shut down and the system is reactivated in Warm Start mode. The keypad lights flash in a repeating
pattern and the heater power is disabled (heating LED will not light).

The display will appear as shown in Figure 18.

Figure 18: Warm Start Display

If this condition occurs:

1.

Turn the BATH power switch off.

2.

After waiting at least five seconds, turn the BATH power switch to the ON position and wait for
the display to indicate either a warm or cold start again.

3.

If the bath comes up in a Cold Start condition and starts its normal self-test sequence, it is likely
that a momentary power interruption caused the Warm Start condition and no further action is
required.

4.

If the bath continues to enter the Warm Start condition, consult CANNON for further assistance.

Self-Test Sequence

The CT-2000 start-up includes a self-test procedure encompassing key components of the system.
These tests, which are displayed on the LCD during start-up, are described in Table 2.

Table 2: CT-2000 Self-Test

Test

Test Purpose

Display

Verifies function of the liquid crystal display (LCD) screen. User may

visually check for bad segments on the display.

32K Ram

Verifies normal operation of CT-2000 system memory.

Pulse Width Modulator

Verifies function of the PWM.

«
...
25
26
27
28
29
...
»

Содержание CT-2000























































Отзывы:

Нет отзывов

Похожие инструкции для CT-2000

Бренд: Campden instruments Страницы: 8

Бренд: ParaBody Страницы: 5

Бренд: Sagola Страницы: 20

Бренд: Earmor Страницы: 5

Бренд: Bante Instruments Страницы: 6

Бренд: Hantek Страницы: 124

Бренд: Hameg Страницы: 10

Бренд: Ultraflex Страницы: 3

Бренд: ParaBody Страницы: 3

Бренд: Valiani Страницы: 66

Бренд: MacDon Страницы: 2

Бренд: Hach Страницы: 456

ZA top SM315.100A

Бренд: ZIEHL-ABEGG Страницы: 76

Implantmed SI-1010

Бренд: W&H Страницы: 2

Бренд: Opvimus Страницы: 50

Бренд: ABB Страницы: 154

DependaBar DB-18-PCW

Бренд: Healthcraft Страницы: 13

Alcotest 7410 GLC

Бренд: Dräger Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды