Canmax Technology CM-2D002 Скачать руководство пользователя страница 66

Страница: 66 / 240

INPUT/OUTPUT SETTINGS

3-17 Illumination Lights

If you want the illumination lights on while reading a bar code, scan the Lights

On bar code, below. However, if you want to turn just the lights off, scan the

Lights Off bar code.

Default = Lights On

Note

: This setting does not affect the aimer light. The aiming light can be set

using

Aimer Mode.

Light On

Light off

3-18 Aimer Delay

The aimer delay allows a delay time for the operator to aim the scan engine

before the picture is taken. Use these codes to set the time between when the

trigger is pulled and when the picture is taken. During the delay time, the

aiming light will appear, but the LEDs won’t turn on until the delay time is over.

Default = Off

200 milliseconds

400 milliseconds

3-17 Illumination Lights

3-18 Aimer Delay

Содержание CM-2D002
















































































































































































































































Результаты поиска

Содержание CM-2D002

Отзывы:

Бренды по названию

Популярные бренды

Canmax Technology CM-2D002, Руководство пользователя

Результаты поиска

Содержание CM-2D002

Отзывы:

Бренды по названию

Популярные бренды