Canmax Technology CM-2D002 Скачать руководство пользователя страница 49

Страница: 49 / 240

INPUT/OUTPUT SETTINGS

3-4-6 LED – Good Read

The LED indicator can be programmed On or Off in response to a good read.

Default = On

LED - Good Read On

LED - Good Read Off

3-4-7 Number of Beeps – Good Read

The number of beeps of a good read can be programmed from 1 - 9. The same

number of beeps will be applied to the beeper and LED in response to a good

read. For example, if you program this option to have five beeps, there will be

five beeps and five LED flashes in response to a good read. The beeps and

LED flashes are in sync with one another. To change the number of beeps,

scan the bar code below and then scan a digit (1-9) bar code and the Save

barcode on the

Programming Chart

inside the back cover of this manual.

Default = 1

Number of Good Read Beeps/LED Flashes

3-4-6 LED – Good Read

3-4-7 Number of Beeps – Good Read

Содержание CM-2D002
















































































































































































































































Результаты поиска

Содержание CM-2D002

Отзывы:

Canmax Technology CM-2D002, Руководство пользователя, Страница: 49 / 240

Результаты поиска

Содержание CM-2D002

Отзывы: