Canmax Technology CM-2D002 страница 192 Скачать руководство пользователя

Страница: 192 / 240

192

SERIAL PROG COMMANDS

Data Field Usage

When a query is used in place of the Data field, the query applies only to the

specific command identified by the Tag and SubTag fields.

Concatenation of Multiple Commands

Multiple commands can be issued within one Prefix/Storage sequence.

Only the Tag, SubTag, and Data fields must be repeated for each command in

the sequence.

If additional commands are to be applied to the same Tag, then the new

command sequence is separated with a comma (,) and only the SubTag and

Data fields of the additional command are issued. If the additional command

requires a different Tag field, the command is separated from previous

commands by a semicolon (;).

Responses

The device responds to serial commands with one of three responses:

ACK Indicates a good command which has been processed.

ENQ Indicates an invalid Tag or SubTag command.

NAK Indicates the command was good, but the Data field entry was

out of the allowable range for this Tag and SubTag combination, e.g., an

entry for a minimum message length of 100 when the field will only

accept 2 characters.

When responding, the device echoes back the command sequence with the

status character inserted directly before each of the punctuation marks (the

period, exclamation point, comma, or semicolon) in the command.

Examples of Query Commands

In the following examples, a bracketed notation [ ] depicts a non-displayable response.

Example

: What is the range of possible values for Codabar Coding Enable?

Enter: cbrena*.

Response:

CBRENA0-1[ACK]

This response indicates that Codabar Coding Enable (CBRENA) has a range of

values from 0 to 1 (off and on).

Example

: What is the default value for Codabar Coding Enable?

Enter: cbrena^.

Response:

CBRENA1[ACK]

This response indicates that the default setting for Codabar Coding Enable (CBRENA) is 1, or

on.

Содержание CM-2D002
















































































































































































































































Результаты поиска

Содержание CM-2D002

Отзывы:

Похожие инструкции для CM-2D002

Бренды по названию

Популярные бренды

Canmax Technology CM-2D002, Руководство пользователя

Результаты поиска

Содержание CM-2D002

Отзывы:

Похожие инструкции для CM-2D002

Бренды по названию

Популярные бренды