Canmax Technology CM-2D002 страница 32 Скачать руководство пользователя

Страница: 32 / 240

PROGRAM THE INTERFACE

2-7 Keyboard Modifiers

This modifies special keyboard features, such as CTRL+ ASCII codes and

Turbo Mode.

C X (C ASCII) Mode On

: The scan engine sends key

combinations for ASCII control characters for values 00-1F. Windows is the

preferred mode. All keyboard country codes are supported. DOS mode is a

legacy mode, and it does not support all keyboard country codes. New users

should use the Windows mode. Refer to

ASCII Conversion Chart (Code Page

1252)

for CTRL+ X Values.

Windows Mode Prefix/Suffix Off

: The scan engine sends key combinations

for ASCII control characters for values 00-1F, but it does not translate any

prefix or suffix information.

Default = C X Mode Off.

Windows Mode C X Mode On

C X Mode Off

DOS Mode C X Mode On

Windows Mode Prefix/Suffix Off

2-7 Keyboard Modifiers

Содержание CM-2D002
















































































































































































































































Результаты поиска

Содержание CM-2D002

Отзывы:

Похожие инструкции для CM-2D002

Бренды по названию

Популярные бренды

Canmax Technology CM-2D002, Руководство пользователя

Результаты поиска

Содержание CM-2D002

Отзывы:

Похожие инструкции для CM-2D002

Бренды по названию

Популярные бренды