Canmax Technology CM-2D002 Скачать руководство пользователя страница 50

Страница: 50 / 240

INPUT/OUTPUT SETTINGS

3-4-8 Number of Beeps – Error

The number of beeps and LED flashes emitted by the scan engine for a bad

read or error can be programmed from 1 - 9. For example, if you program this

option to have five error beeps, there will be five error beeps and five LED

flashes in response to an error. To change the number of error beeps, scan the

bar code below and then scan a digit (1-9) bar code and the Save barcode on

the

Programming Chart

inside the back cover of this manual.

Default = 1

Number of Error Beeps/LED Flashes

3-4-9 Good Read Delay

This sets the minimum amount of time before the scan engine can read

another bar code.

Default = 0 ms (No Delay)

No Delay

Short delay(500ms)

3-4-8 Number of Beeps – Error

3-4-9 Good Read Delay

Содержание CM-2D002
















































































































































































































































Результаты поиска

Содержание CM-2D002

Отзывы:

Бренды по названию

Популярные бренды

Canmax Technology CM-2D002, Руководство пользователя

Результаты поиска

Содержание CM-2D002

Отзывы:

Бренды по названию

Популярные бренды