background image

7

If programming is not required simply close any lids that are open and press the #
key. This will exit engineering mode. Now refer to the users manual for customer
options.

If at any time you wish to exit engineering mode, confirm any options you have
selected with the * (STAR) key, then close ALL tamper circuits and wait for
approximately 60 seconds after which the panel will automatically exit engineering
mode or pressing the # (HASH) key will manually exit engineering

If at any time you wish to re-enter engineering mode, enter the engineering code
and then press the # (HASH) key. This will now force the panel into engineering
mode Note: If left unattended for approximately 60 seconds it will revert to day
mode.

If you need to stay in engineering for longer unattended periods, once in
engineering mode open a tamper circuit. The easiest way to do this is to remove
the lid of the panel or keypad.

PROGRAMMING

Once in engineering mode, the day LED will flash. You now have the following
options available.

EXIT TIME  3 0 (Range 10-90 Seconds.)

Enter 3-0. This has been preset to a factory default of 30 seconds. A new time
may be programmed by entering one key from the following table.

Once the desired option is chosen press * to confirm. The accept tone will sound.

Enter 1

10 Seconds. Led 1 on.

Enter 2

15 Seconds. Led 2 on.

Enter 3

30 Seconds. Led 3 on. (default)

Enter 4

45 Seconds. Led 4 on.

Enter 5

60 Seconds. Led 5 on.

Enter 6

90 Seconds. Led 6 on.

ENTRY TIME

3-1 (Range 10-90 seconds)

Enter 3-1. Again this has been preset  to a factory default of 30 seconds. To
reprogram the entry time follow exactly the same directions as for the EXIT time
(3-0). Again press * to confirm option. The accept tone will sound.

Enter 1

10 Seconds. Led 1 on.

Enter 2

15 Seconds. Led 2 on.

Enter 3

30 Seconds. Led 3 on. (default)

Enter 4

45 Seconds. Led 4 on.

Enter 5

60 Seconds. Led 5 on.

Enter 6

90 Seconds. Led 6 on.

NO
PROGRAMMING
NEEDED?

EXIT
ENGINEERING
MODE

RE-ENTER
ENGINEERING
MODE

STAY IN
ENGINEERING
MODE

TIMERS

EXIT TIME

ENTRY TIME

Содержание S802

















Отзывы: