9
C - USE
Additional instructions:
In case of burn back (ignition under the burner
cap) switch the product off, allow it to cool down
(approximately five minutes), then reignite the
appliance. If the problem of burn back persists,
then please contact your local Campingaz
®
representative.
Do not use your stove at a distance closer than 20 cm
to a wall or any other object, nor closer than 1 meter
to a ceiling.
WARNING: Accessible parts may be very hot. Keep
young children away.
Never touch the pan support (4) or the burner (5)
during or just after using the stove.
Do not obstruct the ventilation holes (7) on the rear
panel and the cartridge compartment cover (3).
Position the stove on a stable, horizontal surface
and do not move when in use.
Wait until the stove has completely cooled down
before handling and putting it away.
Lighting the burner
The stove is fitted with a piezo-electric lighter connected
to an ignition electrode (6).
- Turn the control knob (1) anti-clockwise until you hear
a click ( ) indicating a spark (Fig. 7). If the stove does
not light, turn the control knob to position “
l
” (Fig. 9)
and start the operation again.
- If the stove still does not light after three attempts,
turn the control knob to position “
l
” and check that the
cartridge contains gas (sound of liquid sloshing when
shaken) before starting the previous steps again. (If
the cartridge is empty, refer to section D - Changing
the cartridge).
Cooking
Position the pan on the arms centred over the burner
and adjust the gas flow so that the flames do not burn
higher than the pan.
The size of the flame can be regulated by turning the
ignition knob (1) between the full flow position (MAX)
and minimum flow position (MIN) (Fig. 8).
Extinguishing
Turn the ignition knob (1) clockwise to “
l
” position (Fig. 9).
D - CHANGING THE CARTRIDGE
The cartridge may be removed even if it is not empty.
Once your stove has fully cooled:
- Check that the gas inlet is fully closed by turning the
control knob (1) clockwise to the “
l
” position (Fig. 9)
and that the burner (5) is extinguished.
- Disconnect the cartridge by putting the lever (2) in the
“UNLOCK” position (Fig. 10).
- Open the cartridge compartment (3) and remove the
cartridge by lifting it from behind.
- Never throw away a cartridge which is not completely
empty, (check there is no liquid in the cartridge by
shaking it).
- Make sure that no food has dropped into and thus
obstructs the stove regulator internal housing (Fig. 4)
before installing a new cartridge.
- Check that the seal is present and in good condition
(Fig. 4)
- Put in a new cartridge by following the instructions
in section “B - PREPARATION FOR OPERATION -
Installing a CAMPINGAZ
®
cartridge CP250/ CP250 SP”.
Caution:
If the cartridge is replaced while the stove is in
use, do not touch the hot surfaces of the stove (burner,
saucepan holder, plate...).
Caution:
Gas residue may remain in the stove after
the stove has been turned off. For your safety, with the
cartridge lever (2) in “UNLOCK” position, turn ignition
knob (1) to ( ) position to burn off any remaining fuel.
E - SAFETY DEVICE
Do not use a stove which is leaking, damaged, or which
does not operate properly. If the gas pressure in the
cartridge is too high, two built-in devices stop the gas
flow. The first safety device cuts off the gas passage
while the cartridge remains connected. The second
safety device prevents a potential failure of the first one
(for example, the system could get seized within time).
This second safety disconnects the cartridge and the
lever (2) returns to “UNLOCK”. If any safety is activated,
you must let the cartridge cool down before reusing it or
use a new cartridge following the instructions in Section
“D - CHANGING THE CARTRIDGE”. Moreover, the
safety needs to be reset following the instructions below.
The stove will not operate until the gas pressure of the
cartridge returns back to the normal.
HOW TO RESET SAFETY DEVICE
1
st
safety (gas passage cut off):
- Turn the ignition knob (1) to the “
l
” position and raise
cartridge lever (2) up to the “UNLOCK” position (Fig.
10).
- Remove the gas cartridge.
- Press the red lever near the regulator (Fig. 11).
- Turn the ignition knob to the ( ) position to release
and burn excess gas in the gas cock.
- After 5 minutes, turn the ignition knob to the “
l
”
position.
2
nd
safety (cartridge disconnection)
- Turn the ignition knob (1) to the “
l
” position (Fig. 10).
- Remove the gas cartridge.
- Turn the ignition knob to the ( ) position to release and
burn excess gas in the gas cock.
- After 5 minutes, turn the ignition knob to the “
l
” position.
- Push the cartridge lever down to “LOCK” position (Fig. 6).
- Push the cartridge lever up to “UNLOCK” position (Fig. 10).
If the temperature in the cartridge is high initially, fuel will
not emerge even though the cartridge is installed in the
stove. This is due to the operation of the safety device.
It is not out of order.
GB
