Campbell SP305-L Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 33

background image

2. Attach a mount arm to the top hole on either side of the mount bracket using a bolt, flat

washer, lock washer, and nut. Do not fully tighten either nut.

FIGURE 3-9. Attaching the mount arms

3. Place two support struts together, overlapping the large slot in each strut. Use two bolts,

flat washers, lock washers, and nuts to attach the struts to each other. Do not fully tighten
the nuts. Repeat for the remaining two support struts.

FIGURE 3-10. Assembling the support struts

SP50-L, SP90-L, and SP305-L Solar Panels

12

«
...
12
13
14
15
16
...
»

Содержание SP305-L


































Отзывы:

Нет отзывов

Похожие инструкции для SP305-L

VE1ZZPV W Series

Бренд: GRUPPOSTG Страницы: 23

AFOLUX 915A Series

Бренд: IEI Technology Страницы: 155

Бренд: V-TAC Страницы: 10

VIPA HMI PPC021 ES

Бренд: YASKAWA Страницы: 57

ED-RUD-2 Series

Бренд: Regin Страницы: 6

Бренд: Selec Страницы: 4

Bio Smart Screen

Бренд: Sanuvox Страницы: 9

Бренд: Sharp Страницы: 4

Бренд: Sharp Страницы: 4

Бренд: Sharp Страницы: 8

Бренд: Sharp Страницы: 7

Бренд: Sharp Страницы: 13

Бренд: Leviton Страницы: 83

Бренд: TECOM Страницы: 28

Бренд: Canadian Solar Страницы: 10

Бренд: MR Страницы: 16

Бренд: AGRO ELECTRO Страницы: 19

Бренд: ubbink Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды