manualshive.com logo in svg

CAMERA LINK FC1600FCL, Инструкция по эксплуатации, Страница: 29 / 36

Поделиться
Скачать
CAMERA LINK FC1600FCL Скачать руководство пользователя страница 29

K11208a;29/36 

- 29 - 

Usable special symbols······ SP(H'20), !(H'21), ’(H'27), +(H'2B), comma (H'2C), -(H'2D), .(a full stop mark)(H'2E),   

/(H'2F), : (H'3A), ;(H'3B), <(H'3C), =(H'3D), >(H'3E), ?(H'3F), [(H'5B)], (H'5D), _ (H'5F)   

 
(Note)  When the number of the characters exceeds 15, (transaction rejection) is returned. 
(Note)  When the number of the characters is 0, the ID code is deleted.   
(Note) Carefully note that ID is not correctly written when the character string to be sent includes an unusable character(s). 

This case, however, is not regarded as error ((transaction rejection) is not returned). 

(Note)  This command does not execute the writing into EEPROM and therefore, the setting by this command is lost when 

the power is turned off. If it is necessary to store the setting in EEPROM, transmit another command of “SID”. 

 

(18) Command “SID” 

Function: Command for saving camera ID (set by user) (Save ID) 
 
Transmission from host:  STX: “SID”: ETX 
Return by camera: 

STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection) 

 
The data of the current ID code is saved in EEPROM. 
 
(Note)  The ID code (character string) is saved in a separate area from the program pages, and this common value (one 

numerical number) is applied when the camera is turned on with any one of the program pages.   

(Note)  No ID code is stored before shipment.   
 

(19) Command “RID” 

Function: Command for reading out camera ID (set by user) (Read ID)   
 
Transmission from host:  STX: “RID”: ETX 
Return by camera: 

STX: ACK: “RID”: character string with 0 up to 15 characters: ETX (transaction completion), or 
STX: NAK: ETX (transaction rejection) 

The data (0 up to 15 characters) of the ID code (character string) is read out. When an ID code is not set, the number of 
the characters to be returned is 0.   

 

(20) Command “WVSUB” 

Function: Command for writing Vsub value (CCD substrate voltage) (Write VSUB) 
 
Transmission from host:  STX: “WVSUB”: Vsub setting value: ETX 
Return by camera: 

STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection) 

 
(Note) FC1600FCL does not support this command.   
 

(21) Command “SVSUB” 

Function: Command for saving Vsub value (CCD substrate voltage) (Save VSUB) 
 
Transmission from host:  STX: “SVSUB”: ETX 
Return by camera: 

STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection) 

 
(Note) FC1600FCL does not support this command. 
 

(22) Command “RVSUB” 

Function: Command for reading out Vsub value (CCD substrate voltage) (Read VSUB) 
 
Transmission from host:  STX: “RVSUB”: ETX 
Return by camera: 

STX:  ACK:  “RVSUB”:  Vsub  setting  value:  ETX  (transaction  completion),  or  STX:  NAK:  ETX 
(transaction rejection) 

 

(Note) FC1600FCL does not support this command. 
 

(23) Command “RMG” 

Function: Command for reading MGC gain (Read MGC GAIN) 
 
Transmission from host:  STX: “RMG”: ETX 
Return by camera: 

STX: ACK: “RMG”: MGC setting value: (MGCB setting (right screen)): ETX 

 
(!) FC1600FCL does not use the values in parentheses. 
 

(24) Command “WMG” 

Function: Command for writing MGC gain (Write MGC GAIN) 
 
Transmission from host:  STX: “WMG”: MGC setting value: (MGCB setting (right screen)): ETX 
Return by camera: 

STX: ACK: ETX (transaction completion), or STX: NAK: ETX (transaction rejection) 

 
(!)  FC1600FCL does not use the values in parentheses. Transmit “00” to this camera. 
 
A 2 digit ASCII code from “00” to “FF” in the hexadecimal system is used for the MGC setting value. 

Содержание FC1600FCL





































Отзывы:

Нет отзывов