K11208a;16/36
- 16 -
(Note) When any setting item is changed, it must be saved in one of the program pages from “A” to “F” before turning off
the power to store the data in the memory of the camera. Carefully note that the new setting is not automatically
saved and that the prior setting will be effective at the next time of power-on if the power is turned off before storing
it. The configuration items, however, are automatically saved whenever they are changed.
[Terminology] Configuration items ···· They are the common setting items that are independent of the program pages.
These items are automatically saved in the internal EEPROM at the same time as
they are changed by manipulating the switches on the rear panel.
Table 6-3 Start-up condition for each setting Group
Start-up condition (at time of power-on)
The groups of Operation
Mode Setting
Operation state of camera at
start-up
Position of mode switch
UP/DOWN switch
Arbitrary position
from 0 to F
Neutral position (no switch
manipulation)
Group 1
By normal automatic loading
(
→
Table 6-8)
A
Retention of UP or DOWN
position
Group 2
Start-up with the settings
stored in program page A
C
Group 3
D
Group 4
Table 6-4 Set contents for Operation Mode Setting [Group 1]
Position of
mode switch
Item to be changed
UP/DOWN switch
UP position
DOWN position
0
Change of gain
Increase in gain
Decrease in gain
1
Menu display
(MENU)
<* C>
ON
OFF
2
Preset select 1 or 2
Preset2 (±0dB)
Preset1 (-3dB)
3
Preset select 3 or 4
Preset4 (+12dB)
Preset3 (+6dB)
4
(Not used)
5
Shutter – continuous/asynchronous
(S.FORM )
Continuous
(NORMAL)
Asynchronous
(ASYNC)
6
Shutter – high speed/low speed
(S.TIME)
High speed (HIGH)
Low speed (LOW)
7
Change of shutter speed (S.TIME)
Shorter
Longer
8
Digital offset
(OFFSET)
Increase in offset
Decrease in offset
9
Switch between normal scan/partial scan (SCAN)
All pixels (NORMAL)
Partial (PARTIAL)
A to F
Program pages from A to F
Write
Read
(Note )The decibel value of Preset select is a relative value(reference value) based on Preset 2.
(Note) The shutter speed can be changed only when the shutter switch is currently set at any other positions than “0”.
When the shutter switch is positioned at “0”, the shutter speed cannot be changed even if the mode switch is set to
the position “7” and the UP/DOWN switch is manipulated. (The shutter is always OFF where shutter switch = “0”.)
Table 6-5 Set contents for Operation Mode Setting [Group 2]
Position of
mode switch
Item to be changed
UP/DOWN switch
UP position
DOWN position
1
Menu display
(MENU)
<* C>
ON
OFF
2
(Not used)
-
-
3
(Not used)
-
-
4
Enabled/disabled for pulse width control (PWC) (!)
ENABLED
DISABLED
A to F
Program pages from A to F
Write
Read
(!) When the setting of “ Enabled/disabled for pulse width control” is not set to be “ENABLED”, the pulse width control is
not effective even if the shutter switch is set to the position “9” for the asynchronous shutter operation. In this case, the
preset shutter in asynchronous shutter mode is effective.
Table 6-6 Set contents for Operation Mode Setting [Group 3]
Position of
mode switch
Item to be changed
UP/DOWN switch
UP position
DOWN position
1
Menu display
(MENU) <* C>
ON
OFF
2
Operation confirmation buzzer
(BZ) <* C>
ON
OFF
3
Serial communication baud rate
(BAUDP) <* C>
19200 bps
9600 bps
4
(Not used)
( - )
-
-
5
H-reset in asynchronous shutter mode (H-RESET) <* C>
DISABLED
ENABLED
6
Polarity setting for Vinit2
(Vinit2) <* C>
Positive logic
(INVERTED)
Negative logic
(NORMAL)
7
Continuous shutter strobe signal
(STRB-C) <* C>
ON
OFF
(Note) Although this version of the firmware is designed to display the setting items of (CLOCK), any change made for
these items is disabled and not affect the internal operation. As a general rule, use with the default setting.
(Note) As the external sync operation and the H-reset operation in the asynchronous shutter mode are conflicting, ensure
to select one out of these two operations. If both operation modes are simultaneously selected, it can not function well.
Table 6-7 Set contents for Operation Mode Setting [Group 4]
