background image

Page 

28

 - Manual 

FA01626-EN

  - 02/2023 - © C

AME S.p.A. - The contents of this manual may be changed at any time and without notice. - T

ranslation of the o

riginal instructions

Parameter reset

Restore factory settings except for the functions: [Radio decoding], [Boom length] and the settings related to travel calibration.

A4

Parameter reset

0 =Deactivated (Default)
1 = Activated

Manoeuvre counter

View the number of manoeuvres performed by the operator (1 = 1000 manoeuvres).

A5

Manoeuvre counter

1 = 1000 maneuvers

FW version

Display the firmware version number.

H1

FW version

Import/export data

1

 Insert the MEMORY ROLL card into the corresponding connector on the control 

board.

2

 Press the “Enter” button to access programming.

3

 Use the arrows to choose the desired function.

-F50
Save user data, timings and configurations to the memory device (memory roll or 
USB key).
-F51
Upload user data, timings and configurations from the memory device (memory roll 
or USB key).

 The functions are displayed only when a MEMORY ROLL card is inserted.

 Before inserting and removing the MEMORY ROLL card, DISCONNECT THE 

MAINS POWER SUPPLY TO THE LINE.

 Remove the MEMORY ROLL card after the data has been loaded.

Содержание GARD G3250

































Отзывы: