background image

 

ADDITIONAL INFORMATION FOR INSTALLERS

 

Ensure that the solar power system is installed, expanded, changed and kept in good operating 

condition in accordance with all applicable laws and regulations as well as the generally recognized 

national regulations for   technology. The products must be installed by a licensed electrician in 

accordance with the applicable electrical code (i.e. the NEC for the USA and CEC for Canada).

 

 

After installation, hand over the operating manual as well as the corresponding installation 

documentation (construction drawings, site plans, wiring diagrams, data sheets on components, 

measurement and test reports such as VDE 0126-23 , DIN EN 62446 and so on) to the respective 

operator of the solar power system. Inform the operator that this manual is part of the product and is to 

be kept for the duration of the system’s service life.

 

 

 

ADDITIONAL INFORMATION FOR OPERATORS

 

Request documentation, an acceptance report and an inspection report for the PV system with the 

minimum requirements set out by IEC (DIN EN) 62446 or VDE 0126-23 from the installer.

 

Store these reports together with this manual for the duration of the module’s service life. Without 

presenting these documents, especially the inspection or commissioning report in accordance with the 

above standards, the guarantee or warranty (in accordance with PAS-11-05-0173-EN) shall not apply.

 

 

Pay particular attention to the ‘Troubleshooting’ and ‘Cleaning and maintenance’ sections. For 

information on the formal requirements for solar power systems, please refer to your system suppliers. 

Prior to installing the solar power system, make sure to inform yourself of the guidelines and approval 

requirements set out by the relevant local authorities and energy suppliers. To protect your own 

interests, please obtain the required approvals from authorities as well as the necessary contracts with 

energy suppliers. We recommend that you secure your solar power system against natural hazards (such 

as lightning strikes).

 

Содержание CX1






























Отзывы: