background image

 

PRODUCT  PROTECTION

 

Protect the modules from scratches and other damage, especially impact at the edges and improper 

temporary storage.

 

 

Do not submit the module surface to any mechanical stress. Do not stand on the modules. Do not drop 

or place any objects on the modules.

 

 

Only make changes to the modules that have been previously confirmed by Calyxo in writing. Do not

 

carry out any additional drilling (for example, for fasteners) on the solar modules. Do 

not under any circumstances open the splash-proof junction box. 

 

Never use light concentrators (such as mirrors or lenses or any other means to artificially concentrate 

light) to increase the power output of the modules. Doing so can damage the modules and shall render 

the extended warranty void. 

 

 

 

TRANSPORT AND STORAGE

 

Transport the module in its original packaging through to installation.

 

 

Use a glass suction cup to remove and transport the module, or hold the module by the edges. You need 

to carry the module upright across longer distances.

 

 

Do not under any circumstances lift or move the module by the connecting cables or the junction box!

 

 

Store the module securely in cool and dry rooms. The packaging is not weather-resistant! Do not 

rest the module unprotected on its edges. Doing so can damage the module.

 

Содержание CX1






























Отзывы: