California Accent Lighting lipLEDs LLED8600-RME Скачать руководство пользователя страница 9

Страница: 9 / 21

CALIFORNIA ACCENT LIGHTING, INC.

2034 E. Lincoln Ave. #431, Anaheim, CA 92806

ph. 800.921.CALI (2254) or 714.535-7900 \ fx. 714.535.7902

[email protected] \ calilighting.com

Installation Instructions

lip

LEDs

™

LLED

8600-RME

9 of 21

Setup of Controller (DMX-RGBW-128C)

Cut one end of RJ45 cable near the connector and strip blue jacket, exposing about 1” of

internal wiring.

Connect 12VDC output wires from AC adapter to connector block. Connect the black / white

wire to Power DC+ and the black wire to Power / Ground. Connect the brown /white wire
to DMX Ground, the orange wire to DMX-, and the orange / white wire to DMX+ in the
connector block. Cap off the five remaining wires.

Unbox DMX controller components. You will need the DMX controller, power connector,

software CD-ROM, USB cable, and RJ45 ethernet cable.

Connect AC adapter lead wires to 120V power supply (not included). The dark red wire is

positive and the blue wire is neutral. Do not invert wires as it may damage the controller.

Install Nicolaudie Easy Stand Alone software. Use provided software disc or go to

https://www.nicolaudie.com/en/esa.htm to download software and software manual.

Connect controller via USB cable to a computer with Nicolaudie software installed, then

program scenes into controller as desired. Remove USB cable after programming is complete.

Note:

See page 15 - 16 for a guide on creating and saving customized scenes.

10.

Mount controller interface onto the electrical box. Secure with at least two screws, then snap

the front panel onto the back plate. Wait at least 30 seconds for the touch sensitivity to adjust.

Remove back plate from front panel. Insert a small flathead screwdriver underneath center

tab and gently pry until back plate pops up.

Insert assembled connector block into the receiving port on the back plate of controller.

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

Power Connector 12VDC

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

RJ45 Cable

(Ethernet B Connection)

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

DMX Controller

(#DMX-RGBW-128C)

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

Center tab

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

Conenctor
Block

120VAC input power
source to AC adapter

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)
White / Orange
(DMX +)

Dark Red
(Positive)

AC Adapter

Blue

(Neutral)

White / Brown
(DMX Ground)

Power

DC+

Power

Ground

DMX

Ground

DMX

Orange
(DMX -)

Black / White

(Ground)

Black

(DC +)

White / Orange
(DMX +)

To 120V

Power Source

1 2 3 4 5 6 7 8

1: Orange / White
2: Orange
3: Green / White
4: Blue
5: Blue / White
6: Green
7: Brown / White
8: Brown

On / Off (Short touch)
Mode (Touch and hold)

Front panel

Mounting screw

Mount an electrical box (not included) to the wall where controller will be mounted.

The controller will fit on a standard 60mm electrical box.

Содержание lipLEDs LLED8600-RME






















Результаты поиска

Содержание lipLEDs LLED8600-RME

Отзывы:

Похожие инструкции для lipLEDs LLED8600-RME

Бренды по названию

Популярные бренды

California Accent Lighting lipLEDs LLED8600-RME, Руководство по установке

Результаты поиска

Содержание lipLEDs LLED8600-RME

Отзывы:

Похожие инструкции для lipLEDs LLED8600-RME

Бренды по названию

Популярные бренды