manualshive.com logo in svg

California Accent Lighting lipLEDs LLED8600-RME, Руководство по установке

Поделиться
Скачать
California Accent Lighting lipLEDs LLED8600-RME Скачать руководство пользователя страница 18

CALIFORNIA ACCENT LIGHTING, INC.

2034 E. Lincoln Ave. #431, Anaheim, CA 92806

ph. 800.921.CALI (2254) or 714.535-7900  \  fx. 714.535.7902

[email protected]  \  calilighting.com

© CALI. All rights reserved. CALI reserves the right to make changes or withdraw specifications without prior notice.

Installation Instructions

lip

LEDs

™

LLED

8600-RME

18 of 21

Mounting Channel (Wet Location)

1.

 Measure area where LLED8600-RME will be installed.

     

RECOMMENDATION: 

Use chalk line to ensure a straight installation.

2.

 Drill holes as needed with drill bit and countersink, then screw channel

      to desired surface using countersink holes.

      

NOTE: 

Surface must be flat.

3.

 Remove adhesive backing from lightstrip, then install into channel.

LLED8600

Channel

Remove adhesive backing

Adhere lightstrip 
to channel

7.

 Conduct continuity test.

6.

 Apply silicone at end of run to seal fixture.

8.

 Set voltmeter to DC voltage, then test power source before connecting.

If a conductive 
path is formed 
between positive 
and negative wire, 
the multimeter will 
beep. You need to 
trouble shoot to 
find the short.

If there is no 
conductive path, the 
multimeter will not 
beep.

Troubleshoot

Good

VAC

OFF

VDC

A

COM

Ω 

VΩ 

VAC

OFF

VDC

A

COM

Ω 

VΩ 

+ -

DCA

OFF

DCV

A

COM

Ω 

VΩ 

+ -

VAC

OFF

VDC

A

COM

Ω 

VΩ 

VAC

OFF

VDC

A

COM

Ω 

VΩ 

+ -

DCA

OFF

DCV

A

COM

Ω 

VΩ 

+ -

4.

 Snap lens into channel.

Countersink hole

Ensure screw is 
flush with channel

Apply silicone

5.

 If applicable, slide shrink tube over connectors A1-B1 and apply heat. 

      Shrink tube will shrink down completely to seal the connectors.

Ensure lens is 
secured in place

9.

 Connect power source to power connector. See wiring diagram (page 6).

      

TIP: 

If LEDs do not turn on, flip polarity (+,-) or power source connection to  

                 power connector.

3.9”

3.9”

<1.5”

<1.5”

(<38.1mm)

(<38.1mm)

TRA

6”

4”

<1.5”

<1.5”

.75”

.75”

Apply heat

3.9”

3.9”

<1.5”

<1.5”

(<38.1mm)

(<38.1mm)

TRA

6”

4”

<1.5”

<1.5”

.75”

.75”

Sealed connectors

3.9”

3.9”

<1.5”

<1.5”

(<38.1mm)

(<38.1mm)

TRA

6”

4”

<1.5”

<1.5”

.75”

.75”

Apply silicone 

to seal connections

3.9”

3.9”

<1.5”

<1.5”

(<38.1mm)

(<38.1mm)

TRA

6”

4”

<1.5”

<1.5”

.75”

.75”

Shrink tube

Содержание lipLEDs LLED8600-RME






















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды