background image

Guidelines for first installation

It is good practice to install 

shut-off valves upstream and downstream from the meter

 in order to facilitate installation and maintenance, if 

required.

filtering device

 must be provided upstream of the flow rate meter in order to protect the meter.

With a diameter of 1/2” to 1 1/2”, this strainer is already inside the flow temperature pocket.

Installation procedure

•  

Install the hydraulic components (probe pocket and flow meter) in accordance with the guidelines provided in paragraph “Hydraulic installation 
diagrams” on this page;

• 

After installation, 

wash the pipes and carry out a pressurised test

;

•  Check the saturation level of the strainers

 and, if necessary, clean them;

•  

After completing installation of the hydraulic parts, install the CONTECA

®

 EASY ULTRA electronic unit: follow the instructions for electrical 

connection on pages 5 and 6.

•  

Insert the temperature probes into the corresponding pockets in line with the flow direction: the flow probe (red label) must be installed on the 
flow pipe, while the return probe (blue label) should be on the return pipe. 

•  

At the end of the installation process the main heat meter components (electronics unit, temperature probes and volume meter) should undergo 
lead sealing. 

Lead sealing must be performed by qualified technicians in accordance with the instructions on pages 9 and 10 

(“Lead 

sealing procedure”).

1) Guideline diagram of the system with metering on the multiple circuit manifold.

EASY

CO

N

TECA

EASY

EASY

CO

N

TECA

EASY

EASY

CO

N

TECA

EASY

        M07 1259

07185865

        M07 1259

07185865

        M07 1259

07185865

Hydraulic installation diagrams

The flow meter must be fitted on the 

return pipe.

The hydraulic diagrams provided below show:

a)  

 Flow meter positioning 

   The flow meter 

should preferably be installed

 in a horizontal position, with the axis of the turbine vertical, 

observing 

the flow direction as indicated 

by the arrow on the body. The position of the flow meter, where possible, should result in a zero flow rate when there is no service.

b)  

Probe positioning

    The temperature probes (by means of the pocket or sleeve according to the DN) must be positioned on the corresponding flow/return pipes. The 

corresponding pipes are 

the pipes carrying the same flow rate

 when the flow has started.

3

Содержание CONTECA EASY ULTRA

















Отзывы: