background image

SATK40 & Procyl

®

1

These instructions must be read and understood
before installing and maintaining the HIU.
CAUTION! FAILURE TO FOLLOW THESE
INSTRUCTIONS COULD RESULT IN A SAFETY
HAZARD!

1

The device must be installed, commissioned and 
maintained by qualified technical personnel in accordance 
with national regulations and/or relevant local 
requirements.

2

If the device is not installed, commissioned and maintained
correctly in accordance with the instructions provided in 
this manual, it may not work correctly and may endanger 
the user.

3

Flush the pipework thoroughly before installing the HIU to 
remove any particles, rust, incrustations, limescale, welding
slag and any other contaminants.        
The water circuits must be clean and free from debris.

4

Make sure that all connection fittings are watertight.

5

When connecting water pipes, make sure that threaded 
connections are not mechanically overstressed. Over time 
this may result in breakage, causing water damage and/or 
personal injury.

6

Water temperatures higher than 50˚C may cause severe 
burns. When installing, commissioning and maintaining the
device, take the necessary precautions so that these 
temperatures will not be hazardous for people.

C

ontent

Function and product range

1

Safety instructions

1

Dimensions and technical specification

3

Installation

4

First operation

5

Electronic controller

6

Safety and alarms

7

SATK40 and Procyl

®

components

8

Maintenance

14

Electric connections

16

Trouble shooting and solution

27

Product Range

SATK40103

Wall-mounted indirect Heat Interface Unit 
(HIU) for use with Domestic Hot Water 
(DHW) indirect storage cylinder.

SATK40103 HE

As SATK4013 but with high efficiency pump.

SATK40103

Floor standing or wall mounted indirect Heat 

Procyl

®

Interface Unit (HIU) with Domestic Hot 
Water (DHW) indirect storage cylinder.

SATK40103 HE

As SATK4013 Procyl

®

but with high efficiency

Procyl

®

pump.

Safety Instructions

SATK40103

Function

SATK40 Heat Interface Units (HIU) control the heating and
domestic hot water generation in an individual apartment
within a centralised boiler or district heating system.

NOTE:

Due to the specification ordered, or the country of

destination, the actual unit may differ from those shown.

WARNING

Содержание Altecnic SATK40103

















Отзывы: