background image

3

WIRED REMOTE CONTROLLER BUTTONS

Enter/cancel

Enter/Cancel

Fan

Mode

Function

Timer

On/Off

1

4

5

6

7

8

2

3

Fig. 4

 - 

Wired Remote Controller Buttons

WIRED REMOTE CONTROLLER BUTTON FUNCTIONS

Table 2—Controller Button Functions

n

o

i

t

c

n

u

F

e

m

a

N

.

o

N

1

Enter/Cancel

Function selection and cancellation

2

 Running temperature setting of the indoor unit, range:
 Timer setting, range:0.5-24 hr

6

3

Fan

Setting of the high/middle/low/auto fan speed

4

Mode

Setting of the Cooling/Heating/Fan/Dry/Auto mode of the indoor unit

5

Function

Switchover among the functions of Turbo

/

Save/E-heater/Blow etc.

7

Timer

Timer setting

8

On/Off

Turn on/off the indoor unit

4+2

Press for 5s under t h e  u n i t ’ s  OFF state to Enter/Cancel the Memory 
function (If the memory is set, t h e  indoor unit after a  power failure and 
power recovery resumes the original setting state. If not, the indoor
unit defaults to OFF after a  power recovery. MEMORY OFF is t h e  
default prior to delivery).

3+6

Press at the same time under the unit’s OFF state,    appears on the  
wired remote controller for the COOLING ONLY unit, while 
the wired remote controller for the cooling and heating unit. 

2+6

Upon u n i t  startup ( without malfunction) or under t h e  u n i t ’ s  OFF state,

 

press both at the same time for 5s to enter the lock state, in which 
case, no other buttons will respond i f  p r e s s e d . Press them a g a i n
together for 5 secs to exit the mode.

4+6

If there is a preference for °F rather than °C (default), under OFF state press

5+7

FTimer

Under  t h e   OFF  state,  the user can select  the  commissioning  status  by
pressing FUNCTION and TIMER for five secs. 00 appears on the temp. display 

when MODE is pressed,  then  adjust  the  options shown in the timer area by
pressing    and   . There are four options: 

 Indoor ambient temperature is sensed by the return air temperature 

sensor ( 01 displayed on the timer area).

 Indoor ambient temperature is sensed by the wired controller (02 

displayed on the timer area).

 The return air temperature sensor is selected under the cooling, dry, or 

fan mode; while the wired controller temperature sensor is selected under 
the heating or auto mode (03 is displayed on the timer area).

 The wired controller temperature sensor is selected under the cooling, 

dry, or fan mode; while the return air temperature sensor is selected under 
the heating mode. (04 is displayed on the timer display area).

5+7

FTimer

Under t h e  OFF state, users can access the commissioning status by 
pressing FUNCTION and TIMER for five secs. Press MODE until “01”

appears in the temperature display area. The setting status appears in the
timer area. Press   and   to adjust. The two options are:  

Three low levels (01) ; 

Three high levels (02).

o

60.8 F~

o

o

o

86 F(16 C~30 C)

 appears on  

and hold MODE and decrease temp. set point buttons together for 5 secs.

Содержание KSACN0301AAA











Отзывы: